Vaisala AWS310-SITE Скачать руководство пользователя страница 136

Страница: 136 / 176

Problem

Probable Cause

Remedy

Serial communication is

inconsistent or data is
missing.

Pin contacts of the connector

have become oxidized or the
connector is not firmly

attached.

Change the WMT700 cable.

For further instructions, see

Vaisala Automatic Weather Station AWS310 / AWS310-SITE

Installation Manual

6.8 Troubleshooting WA15

6.8.1 Problem Situations with WAV151

Table 33 WAV151 Problem Situations and Their Remedies

Problem

Probable Cause

Remedy

Data is not received from the
sensor.

The sensor is not powered
properly.

Check that the supply voltage is 9.5 … 15.5
VDC.

Improper or loose
connections.

Check the wiring and tighten the screw
terminals.

After removing the
connector's hex nut, the

connector is bent, which
breaks the connection wires.

Check the connector.

The sensor is mechanically
damaged.

Send the sensor to Vaisala for repair.

Sensor body is covered with
ice and snow.

Sensor heating does not
function.

Check the status indicator of the surge
arrester. If the indicator is red, change the

removable plug in the surge arrester.
Heating is disabled when the system is
running on backup battery. Check that the

power cable is connected (the cable is not
loose).

Heating element is not
properly connected or does

not function.

Send the sensor to Vaisala for repair.

Output from the connector
pins

does not have the

right code or is not at the
proper level.

The printed circuit board is
damaged.

Send the sensor to Vaisala for repair.

When you rotate the shaft

mechanically, current
consumption is less than
17 mA or more than 25 mA .

AWS310-SITE Configuration and Maintenance Manual

M211828EN-C

134

Содержание AWS310-SITE

















































































































































































Результаты поиска

Содержание AWS310-SITE

Отзывы:

Бренды по названию

Популярные бренды

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Результаты поиска

Содержание AWS310-SITE

Отзывы:

Бренды по названию

Популярные бренды