Vaisala AWS310-SITE Скачать руководство пользователя страница 124

Страница: 124 / 176

When the direct connection to a sensor is open, any automatic operation through the
connected port is blocked.

1. Open a terminal connection to the QML data logger.

2. To enter the service mode, type the command

open

3. To open a direct connection to a sensor, type the appropriate command.

Sensor

Command to Open Service
Connection

Command to Open Sensor

CL31

open DSI486_0_0

OPEN 8

HMP155 (serial)

open DSI486_0_0

OPEN 10

PTB330

open DSI486_1_0

OPEN 20

PWD22

open DSI486_0_0

OPEN 7

Primary wind sensor

open COM1

$AOPEN

(WMT700)

OPEN K

(WA15)

Secondary wind sensor

open DSI486_0_0

$BOPEN

(WMT700)

OPEN L

(WA15)

4. When finished with the configuration, terminate the service connection to the sensor

and the service connection to the QML data logger by typing the command

close

6.5.4 Troubleshooting Connection Problems

If you cannot connect to the QML data logger, the service connection is not opened and you
cannot work with the logger.

Table 28 Common Connection Problems and Their Remedies

Problem

Probable Cause

Remedy

You receive the message

Failed

to open terminal

connection

You are trying to connect to the
wrong port.

To check the port numbers, in AWS
Client, select

Settings > Address

Book

Cables are not connected.

Check that the modem cable is
connected properly.

You receive the message

Failed

to open connection

You are trying to connect to a port
that does not exist on your

computer.

Check the port settings.

The port is reserved (some other
program is connected to it).

Check that the terminal window is
not already open.

You do not receive any messages.

Cables are not connected.

Connect the cables.

AWS310-SITE Configuration and Maintenance Manual

M211828EN-C

122

Содержание AWS310-SITE

















































































































































































Результаты поиска

Содержание AWS310-SITE

Отзывы:

Похожие инструкции для AWS310-SITE

Бренды по названию

Популярные бренды

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Результаты поиска

Содержание AWS310-SITE

Отзывы:

Похожие инструкции для AWS310-SITE

Бренды по названию

Популярные бренды