Vaisala AWS310-SITE Скачать руководство пользователя страница 121

Страница: 121 / 176

6.4 Basic Troubleshooting

Table 26 Problem Situations and Their Remedies

Problem

Probable Cause

Remedy

No data received from
the sensor.

The sensor not enabled in
the

CFG

parameter set.

Enable the sensor in the

CFG

parameter set.

Battery status LED of the
battery regulator is not
lit.

AC (mains) power is off.

Check the battery status and make sure that the
battery regulator is working:

1. Press the status button on the battery regulator.

2. Check if the AC (mains) is off.
3. If yes, switch the AC (mains) on. If not, use a

multimeter to measure if the battery regulator is
getting power.

Battery is empty.

Replace the battery.

The battery regulator
does not work, although
it is getting power.

The battery regulator is
broken.

Replace the battery regulator.

Green LED does not light
on all power supplies.

Power supply is not
working.

Use a multimeter to measure if the power supply is
getting AC power. If yes, replace the power supply.

Green LED on the QML
data logger is not

blinking, no data is shown
on the displays, or no
report is sent over the

communication
connection.

QML data logger does
not get power.

1. Use a multimeter to measure if the QML data

logger is getting power.

2. If not, check that all the power supply and battery

cables are intact and connected. If yes, try
establishing a service connection with

COM0

and

a maintenance cable.

3. Set the terminal settings to

9600

and type

the command

open

. If the QML data logger

answers with service connection, it is working.

4. To check the error messages from the QML data

logger, type

errors

5. To get the warning messages from the QML data

logger, type

warnings

. The warning messages

are not usually serious, but useful for

troubleshooting.

6. To get system uptime information, type

sysinfo

7. To reset the QML data logger, type

reset

8. To get the debugging report, type

TABLE

9. To close the service connection, type

close

QML data logger may be

damaged.

One of the
communication modules

may be broken.

QML data logger
configuration may be

broken.

Chapter 6 – Troubleshooting

119

Содержание AWS310-SITE

















































































































































































Результаты поиска

Содержание AWS310-SITE

Отзывы:

Бренды по названию

Популярные бренды

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Результаты поиска

Содержание AWS310-SITE

Отзывы:

Бренды по названию

Популярные бренды