manualshive.com logo in svg

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Поделиться
Скачать
Vaisala AWS310-SITE Скачать руководство пользователя страница 108

5.9.2 Sending HMP155 for Calibration

Once a year, or if the sensor readings seem inaccurate, send HMP155 to Vaisala for
calibration. Replace it with a calibrated spare probe, if available, or wait until Vaisala sends
the probe back from calibration.

1. Remove the probe from inside the radiation shield.

2. Send the probe to Vaisala for calibration.
3. Check the operation of the calibrated probe by warming the sensor head with your

hand, and monitor the value change.

4. Place the calibrated probe inside the radiation shield.

5.9.3 Adding HMP155 to System

Before configuring the new sensor, complete the mechanical installation.

1. In AWS Client, select 

Settings > Parameters > Static

.

2. In the 

CFG

 parameter set, select 

HMP155

 (serial sensor) or 

HMP155_ANL

 (analog

sensor).

3. To enable the sensor, type 

1

 in the 

Value

 field, and select 

Save

.

4. In the 

RH_Selector

 parameter set, select the relative humidity sensor to use. 

•

1

 = HMP155 (serial)

•

2

 = HMP155 (analog)

5. In the 

TA_Selector

 parameter set, select the air temperature sensor to use. 

•

1

 = HMP155 (serial)

•

2

 = HMP155 (analog)

6. To activate the new configuration, reset the QML data logger. Select 

Maintenance > 

Reset > Immediate

.

5.10 RG13(H) Maintenance

To ensure accurate operation, keep the sensor clean. Clean the sensor at least every
6 months. When leaves are falling and there is a lot of debris in circulation, check the sensor
more often.

To avoid erroneous measurements, avoid tipping the cup assembly when the gauge is
connected to the weather station and the station is operating.

To ensure reliable and accurate measurements, Vaisala recommends you to carry out the
following checks at each visit to the rain gauge.

1. Inspect the funnel and filter for any damage or blockage.

2. Remove any obstacles from the funnel, such as leaves, debris, dirt, and dust.
3. Clean the filter by removing the end cap from the filter tube.

AWS310-SITE Configuration and Maintenance Manual

M211828EN-C

106

Содержание AWS310-SITE

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды