background image

Maintenance and care 6

0020213396_00 flexoTHERM Operating instructions

13

Operating hours for heating mode, hot
water handling mode, cooling mode and
the overall operation

5.8 Setting the language

Menu

Basic settings

Language

Setting the desired language

6 Maintenance and care

6.1 Checking and maintaining
6.1.1 Fulfilling requirements for the

installation site

The installation site must be dry and frost-
proof throughout.

Conditions

: Outdoor air heat source

The air/brine collector is designed to be
operated with outdoor air. The air intake
and blow-off route of the outdoor unit must
be kept clear at all times in order to guar-
antee that the air can flow unhindered and
as intended. Vegetation and, in winter,
snowfall, must be cleared.
You are not permitted to make any sub-
sequent structural alterations which
may result in a reduced room volume
or a change to the temperature at the
installation site.

6.1.2 Caring for the product

Caution.
Risk of material damage

caused by unsuitable clean-

ing agents.

Do not use sprays, scouring

agents, detergents, solvents

or cleaning agents that con-

tain chlorine.

Clean the casing with a damp cloth and
a little solvent-free soap.

6.1.3 Checking the system pressure

Check the filling pressure of the heating
installation every day for a week after
initial start-up and maintenance work,
and then twice a year.

Filling pressure:

0.07 MPa

(

0.70 bar)

Filling pressure too low

Inform your competent person so
that he can add heating water and
increase the filling pressure.

6.1.4 Checking the brine circuit's

filling pressure

Check the brine circuit's filling pressure
at regular intervals. Read the brine cir-
cuit's filling pressure in the heat pump's
display.

Brine fluid operating pressure range:
0.07 … 0.20 MPa (0.70 … 2.00 bar)

7 Troubleshooting

7.1 Fault message

If several faults occur at the same time,
the display shows the corresponding fault
messages for two seconds each in alterna-
tion.

F.714 Environment circuit: Pressure too
low

If the filling pressure falls below the min-
imum pressure, the heat pump will be
switched off automatically.

Minimum brine fluid pressure:

0.05 MPa (

0.50 bar)

Min. brine fluid operating pressure:

0.07 MPa (

0.70 bar)

Inform your competent person so that
he can top up the brine fluid.

F.723 Building circuit: Pressure too low

If the filling pressure falls below the min-
imum pressure, the heat pump will be
switched off automatically.

Содержание flexoTHERM VWF 5x





















Отзывы: