manualshive.com logo in svg

Vaillant ecoTEC plus VUI Series, Инструкция по установке и обслуживанию

Поделиться
Скачать
Vaillant ecoTEC plus VUI Series Скачать руководство пользователя страница 19

0020308121_04 Installation and maintenance instructions

19

7.2.4

Flue Configuration Description

7.2.4.1 Horizontal Concentric Flue

⌀

60/100 mm or

⌀

80/125 mm (C13 type installation)

1

1

Gasket (fitted)

Note

If the terminal is at less than 2.0 m from the
ground, you must install a terminal protection kit.

Consult the separate installation manual for air/flue gas sys-
tems supplied with your appliance for all possibilities and as-
sociated accessories and how to install the flue system.

7.2.4.2 Terminal protection

A terminal guard is required if persons could come into con-
tact with the terminal or the terminal could be subject to dam-
age.

If a terminal guard is required, it must be positioned to
provide minimum of 50 mm clearance from any part of the
terminal and be central over the terminal.

The guard should be stainless and similar to that shown in
the figure.

7.2.4.3 Vertical Concentric Flue

⌀

60/100 mm or

⌀

80/125 mm (C33 type installation)

Consult the separate installation manual for air/flue gas sys-
tems supplied with your appliance for all possibilities and as-
sociated accessories and how to install the flue system.

7.2.5

Installing and connecting the air/flue pipe

1.

You can find out which air/flue pipes may be used
by consulting the enclosed set-up instructions for the
air/flue system.

2.

Observe the information on positioning the air/flue ter-
minal.

Condition

: Installation in damp rooms

▶

You must connect the product to a room-sealed air/flue
system. The combustion air must not be taken from the
installation site.

Caution.
Risk of poisoning due to escaping flue
gas.

Mineral-oil-based greases can damage the
seals.

▶

Instead of grease, use only water or com-
mercially available soft soap to aid install-
ation.

3.

Install the air/flue pipe using the set-up instructions.

Содержание ecoTEC plus VUI Series





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды