Vaillant ecoTEC plus VU 6/5-5 Series Скачать руководство пользователя

Страница: 49 / 80

0020244997_07 Installation and maintenance instructions

13.6.6 Replacing the expansion vessel

Drain the product. (

→

Page 44)

3
4

Undo the screwed connection

(4)

Remove both screws

(1)

on the support plate

(2)

Remove the support plate

(2)

Pull out the expansion vessel

(3)

towards the front.

Insert the new expansion vessel into the product.

Screw the new expansion vessel to the water connec-
tion. Use a new seal for this.

Attach the support plate using both screws

(1)

Fill and purge the product and, if necessary, the heat-
ing installation. (

→

Page 35)

13.6.7 Replacing the PCB or the display

Note

If you only replace one component, when the
product is switched on, the new component ad-
opts the parameters that were previously set from
the component that was not replaced.

Open the electronics box. (

→

Page 28)

Replace the PCB or display according to the set-up
and installation instructions supplied.

X12

If you are replacing the PCB, remove the coding res-
istor

(1)

(plug X24) from the old PCB and plug the plug

onto the new PCB.

Close the electronics box.

13.6.8 Replacing the PCB and the display

Open the electronics box. (

→

Page 28)

Replace the PCB and display according to the set-up
and installation instructions supplied.

X12

Remove the coding resistor

(1)

(plug X24) from the old

PCB and plug the plug into the new PCB.

Close the electronics box.

Press the product's on/off button. (

→

Page 32)

◁

After switching on, the product switches directly to
the menu to select the language. The factory-set
language setting is English.

Select the required language and confirm by pressing

◁

You are automatically taken to

D.093

to set the

device specific number.

Set the correct value for the relevant product type in
accordance with the table below and confirm by press-
ing

Product type number

VU 126/5-5 (H-GB) ecoTEC
plus 612

VU 156/5-5 (H-GB) ecoTEC
plus 615

VU 186/5-5 (H-GB) ecoTEC
plus 618

VU 186/5-5 (P-GB) ecoTEC
plus 618

VU 246/5-5 (H-GB) ecoTEC
plus 624

VU 306/5-5 (H-GB) ecoTEC
plus 630

VU 306/5-5 (P-GB) ecoTEC
plus 630

VU 386/5-5 (H-GB) ecoTEC
plus 637

VUW 196/5-5 (H-GB) ecoTEC
plus 825

VUW 246/5-5 (H-GB) ecoTEC
plus 832

VUW 246/5-5 (P-GB) ecoTEC
plus 832

VUW 306/5-5 (H-GB) ecoTEC
plus 835

VUW 286/5-5 (H-GB) ecoTEC
plus 838

◁

The electronics are now set to the product type and
the parameters of all diagnostics codes are set to
factory settings.

◁

The installation assistant starts.

Make the system-specific settings.

Содержание ecoTEC plus VU 6/5-5 Series

















































































Результаты поиска

Содержание ecoTEC plus VU 6/5-5 Series

Отзывы:

Похожие инструкции для ecoTEC plus VU 6/5-5 Series

Бренды по названию

Популярные бренды

Vaillant ecoTEC plus VU 6/5-5 Series, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ecoTEC plus VU 6/5-5 Series

Отзывы:

Похожие инструкции для ecoTEC plus VU 6/5-5 Series

Бренды по названию

Популярные бренды