Vacon 100 HVAC Скачать руководство пользователя

Страница: 21 / 201

Set the signal range of the analogue input

0 = 0-10V / 0-20mA

1 = 2-10V / 4-20mA

See Table 15 Analogue input settings.

Set a value for Keypad Setpoint 1 (P3.12.2.1) and

Keypad Setpoint 2 (P3.12.2.2)

Depends on the range set in the question 9.

Using the sleep function

0 = No

1 = Yes

If you give the value Yes for the question 11, you see the next 3 questions. If you give the value

No, the wizard is completed.

Set a value for Sleep Frequency Limit (P3.12.2.7)

Range: 0.00-320.00 Hz

Set a value for Sleep Delay 1 (P3.12.2.8)

Range: 0-3000 s

Set a value for Wake-up Level (P3.12.2.9)

The range depends on the set process unit

The PID mini-wizard is completed.

2.2

MULTI-PUMP MINI-WIZARD

The Multi-pump mini-wizard asks the most important questions to set up a Multi-pump

system. The Multi-pump mini-wizard always follows the PID mini-wizard.

Set a value for Number of Motors (P.3.14.1)

1-4

Set a value for Interlock Function (P3.14.2)

0 = Not used

1 = Enabled

Set a value for Autochange (P3.14.4)

0 = Disabled

1 = Enabled

If you enable the Autochange function, you see the next 3 questions. If you do not use the

Autochange function, the wizard goes directly to question 21.

WIZARDS

VACON · 21

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды