Vacon 100 HVAC Скачать руководство пользователя

Страница: 175 / 201

P3.13.1.2 OUTPUT IN STOP (ID 1100)

Use this parameter to set the output value of the PID controller as a percentage of its

maximum output value when it is stopped from a digital output.

10.14

MULTI-PUMP FUNCTION

The Multi-pump function lets you control a maximum of 4 motors, pumps or fans with the

PID controller.

The AC drive is connected to a motor, which is the regulating motor. The regulating motor

connects and disconnects the other motors to/from the mains with relays. This is done to

keep the right setpoint. The Autochange function controls the sequence in which the motors

start to make sure that they wear equally. You can include the regulating motor in the

autochange and interlock logic, or set it to always be Motor 1. It is possible to remove motors

momentarily with the Interlock function, for example for maintenance.

ON
OFF
ON
OFF

Delay

Bandwidth

Feedback

Setpoint

Drive is running at maximum

or close to maximum frequency

Fig. 44: The Multipump function

If the PID controller cannot keep the feedback in the set bandwidth, a motor or motors are

connected or disconnected.

When to connect and/or add motors:

•

The feedback value is not in the bandwidth area.

•

The regulating motor operates at a close to maximum frequency (-2 Hz).

•

The conditions above are true for longer than the bandwidth delay.

•

There are more motors available

PARAMETER DESCRIPTIONS

VACON · 175

24-HOUR S358 (0)201 212 575 · EMAIL: [email protected]

Содержание 100 HVAC










































































































































































































Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды

Vacon 100 HVAC, Руководство по применению

Результаты поиска

Содержание 100 HVAC

Отзывы:

Похожие инструкции для 100 HVAC

Бренды по названию

Популярные бренды