UWT Nivobob NB 4000 Скачать руководство пользователя | Manualshive

Страница: 16 / 22

background image

Continuous level measuring system

NB 4000

Technical information / Instruction manual

page G

Programming

To reset all programmed parameters to factory setting (default values), press the buttons ARROW UP, ARROW DOWN and SETUP
together for approx. 10 seconds.

Programming buttons

Continues with next adjustment item

Continues with measurement display after parameter adjustment
Starts measurement

Cancels a Failure message (when pressed 2 sec together with SETUP button)

Increases the value to be adjusted

Decreases the value to be adjusted

Factory settings

Runtime messages

During measurement mode, following runtime indications are given:

*

Upper Stop Position is reached

Motor is moving the sensor weight downwards resp. upwards (fast mode)

Motor is moving in slow mode (shortly after motor start and before
Upper Stop Position is reached)

Measurement interruption is active (terminal 24-26 not connected, see page
G12)

Note:
Pressing the ARROW DOWN
button in measurement
mode brings up more
service information (not
described in this manual)

Nivobob

®

1

2

3

4

5

6

7

8

9

10

11

12

NB 4000

gi010413

16

Blocked 24-26 open

«
...
14
15
16
17
18
...
»

Содержание Nivobob NB 4000























Отзывы:

Нет отзывов

Похожие инструкции для Nivobob NB 4000

Бренд: AccuMASTER Страницы: 2

Бренд: Yamaha Страницы: 83

Бренд: Yamaha Страницы: 63

Бренд: 4iiii Страницы: 3

Бренд: Vanguard Instruments Страницы: 24

Бренд: UEi Страницы: 8

Бренд: marposs Страницы: 58

PLUS 3631 Series

Бренд: insize Страницы: 1

Бренд: Datakom Страницы: 28

STORA-ABG RKS-01

Бренд: ECOTEST Страницы: 146

Бренд: Trotec Страницы: 14

Ratio:Guard Advanced

Бренд: H.E. Anderson Страницы: 9

Amplitude T Series

Бренд: OTOVATION Страницы: 15

Бренд: Hanna Instruments Страницы: 32

Бренд: Pfeiffer Vacuum Страницы: 28

Бренд: MAC Страницы: 143

Бренд: Meters UK Страницы: 11

Бренд: Huazheng Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды