manualshive.com logo in svg

UTICA BOILERS UH15B-060K, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
UTICA BOILERS UH15B-060K Скачать руководство пользователя страница 41

41

A.9 Intermittent Pilot

Ignition System Checks

STEP 1: 

Check ignition cable.

• Verify ignition cable does not make contact with metal 

surfaces.

• Verify only factory supplied Ignition cable (or approved 

replacement) is used.

• Verify connections to ignition module and igniter or 

igniter-sensor are clean and tight.

• Verify ignition cable provides good electrical continuity.

STEP 2:

Verify ignition system grounding. Nuisance shutdowns are 

often caused by poor or erratic grounding.

Common ground is required for module and pilot  burner/

igniter sensor.

— Check for good metal-to-metal contact between pilot 

burner bracket and the main burner.

— Check ground lead from GND (BURNER) terminal 

on module to pilot burner.  Verify connections are 

clean and tight. If wire is damaged or deteriorated, 

replace with No. 14-18 gauge, moisture-resistant, 

thermoplastic insulated wire with 105°C [221°F] 

minimum rating.

— Check ceramic flame rod insulator for cracks or 

evidence of exposure to extreme heat, which can 

permit leakage to ground. Replace pilot burner/igniter 

sensor and provide shield if necessary.

— If flame rod or bracket is bent out of position, restore 

to correct position.

STEP 3:

 Check spark ignition circuit. 

Disconnect ignition cable at SPARK terminal on module.

APPENDIX A - CONTROL MODULE

 PN 240012809, Rev. D [08/15/2021]

Содержание UH15B-060K

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды