Uson sprint iq Скачать руководство пользователя страница 20

Страница: 20 / 122

Quick Start

2.2.8.1 Fine Tuning

After you’ve entered the basic parameters into a program, you’re
ready to fine-tune your setup. A few tips:

• If not using external fixtures, set coupling time to zero.

• If product blows out of external fixtures, make sure you

have a long enough coupling time.

• If you get gross failures when testing a flexible product, try

increasing fill time or evacuate (for vacuum tests) time.

• Add fill and stabilize time to slow the decay rate and make

it more consistent.

• If your test doesn’t need a dump valve to vent product

pressure after testing, set the vent parameter to off.

• In a flow test, set test time long enough for the product

under test to fill and produce a stable flow rate.

• If repeated parts failures of good parts occur, try widening

the pressure error tolerance or adding more fill or evacuate
(for vacuum tests) time.

2.2.9 Put Sprint iQ to Work

When everything is programmed and checked out, you’re ready to
put Sprint iQ to work and start testing products. A few tips:

• Explain controls and run display messages to operators.

• Keep external connections to the product under test as

straight, rigid, and direct as possible. Flexible connections
can cause inconsistent readings.

• Put Sprint iQ in a place where the pressure regulator and

other controls on the back won’t get moved around or
damaged.

Содержание sprint iq



























































































































Результаты поиска

Содержание sprint iq

Отзывы:

Бренды по названию

Популярные бренды

Uson sprint iq, Руководство пользователя

Результаты поиска

Содержание sprint iq

Отзывы:

Бренды по названию

Популярные бренды