background image

Page 7 

 

VDE Certified Power Cords. 

 

Pollution:  Not intended for environments where conductive pollutants may be present. 

 
2.2

 

 

Equipment Class 

Type A:  Equipment that is intended for connection to the building power supply wiring via nonindustrial plugs and 
sockets or via appliance couplers, or both. 
 

2.3

 

 

Disposal and Recycling 

Wheelie-Bin Symbol 

The  Wheelie-Bin  symbol  is  attached  to  this  product  in  compliance  with  the  EU  Directive  2002/96/EC  on 
Waste Electrical and Electronic Equipment  (WEEE).   Its purpose is to deter the improper disposal of this 
product and to promote reuse and recycling. 

 
Proper Disposal 

In  conformance  with  the  Directive,  at  end  of  life  this  product  should  be  either  sent  to  an  appropriate  recycling 
facility for disassembly and recycling or returned to the supplier.  Under no circumstances should this product be 
deposited in a landfill for disposal. 
 

Hazards of Noncompliance  

Electrical and electronic products may contain chemicals which can leach into the groundwater and cause health 
concerns through contaminated drinking water.   Failure to dispose of this product in compliance with the WEEE 
Directive may result in penalties as determined by local ordinance.

 

 
Please  contact  your  dealer  or  USL,  Inc.,  with  questions  regarding  the  proper  disposal  of  this  or  any  other  USL 
product.    USL,  Inc.  contact  information:    USL,  Inc.,  181  Bonetti  Drive,  San  Luis  Obispo,  CA    93401-7397,  USA.  
Phone:  +1 805 549 0161     Fax:  +1 805 549 0163     

www.uslinc.com

 

 

3.

 

 System Version 

 

The  JSD-100  is  continuously  being  improved.    New  features  are  added  through  software/firmware  updates  and 
replacement of plug-in modules. This manual describes the JSD-100 versions available at this writing.   Upcoming 
features that are mentioned here but not yet implemented include internal crossovers and 32 channel AES output 
module.  Contact USL for the availability of these features. 
 
Firmware/software versions for the systems described in this manual are listed in the table below: 

 

 
 
 

 

4.

 

 System Overview 

 
4.1

 

System Description 

The  JSD-100  cinema  sound  processor  is  specially  designed  for  digital  cinema  applications.    Low  noise  and  low 
distortion 96 kHz processing ensures superb presentations.  In addition to the eight standard formats, the JSD-100 
offers two fully configurable formats.  The two user-configurable buttons can be configured to support a variety of 
existing and future formats.  They may also be used to duplicate an existing format but at a different fader level to 
simplify desired volume changes between content types.  The front panel display shows the current fader level, the 
format name (which is user configurable), and the measured audio level on each channel of the main audio output.  
The built-in bypass audio circuitry insures that the presentation goes on in the unlikely event of a system failure. 
 

Component 

Version 

Graphical User Interface (GUI) 

2.1.7.16374 

Main PIC 

110630 

DSP 1 

1110525 

DSP 2 

2110525 

Содержание Cinema Processor















































Отзывы: