setting up your remote control
button functions
before you begin
*
displays help for on-screen display screens
#
future use
MUSIC/ENTER
switches between cable TV and Music Choice™
LAST
recalls the last channel that was viewed
FAV
cycles through your favorite channels
MUTE
turns volume off
P
displays the quick function screen
◆
future use
PPV
displays pay-per-view options
EXIT
exits the on-screen display menus
INFO
displays channel and program information
MENU
displays the main on-screen display menu
GUIDE
displays the program guide
SEL
selects various options and tunes programs from the program guide
CURSOR KEYS
navigate through on-screen guides (see the highlighted section above)
PAGE +/-
pages through on-screen menu and program guide screens
DAY +/-
moves the program guide one day forward and backward
EPG RECORD
initiates VCR recording through the on-screen menu (if so equipped)
© 1998 US Electronics Components Corp. All rights reserved
Part Number USE17370, Version 1.1
9804
User’s Guide for the
UY322-EPG
3-in-1 Remote Control
featuring Memory Lock
™
and Predictive Technology
™
Install two
AAA alkaline batteries
as shown here
If you have a TV with a remote control, we
recommend that you plug its power cord
directly into a wall outlet if available (your
cable installer may select an alternate setup).
Make sure to set your TV to channel 2, 3, or 4
as directed by your cable company.
Before you can program or operate the remote
control, you must install two AAA Alkaline
batteries.
Step 1
Remove the battery compartment cover on the
back of your remote control.
Step 2:
Check battery polarity carefully,and
install the batteries as shown in the
illustration below.
Step 3:
Replace the battery compartment cover.
installing batteries
The chart below shows the functions of special keys for your cable box and program guide.
See the cable box manual for further details.
MORE
INFO
step
2
Press the
[TV POWER]
button,then the
[SETUP]
button on the remote.
Enter the 3-digit TV code for your brand of TV listed in the “TV codes”chart.
Press the
[SETUP]
button again to save the code. The red indicator light at the upper
right-hand corner of your remote will flash 3 times if these steps were followed correctly.
Press the
[TV POWER]
button again to test the code you‘ve entered. The TV should
turn ON or OFF each time the
[TV POWER]
button is pressed. If the TV doesn’t turn
ON and OFF, repeat this TV setup procedure with the next code listed in the “TV
codes” chart.
step
3
Press the
[CABLE POWER]
button,then the
[SETUP]
button on the remote.
Enter the 3-digit cable box code listed below.
Press the
[SETUP]
button again to save the code. The red indicator light at the upper
right-hand corner of your remote will flash 3 times if these steps were followed correctly.
Press the
[CABLE POWER]
button again to test the code you‘ve entered. The cable box
should turn ON or OFF each time the
[CABLE POWER]
button is pressed.If the cable box
doesn’t turn ON and OFF,try entering the code again.
Follow these simple steps to program your remote for your VCR,TV,and cable box.
Before you start
■
Locate the
[SETUP]
button, which is at the very bottom of the
remote (see illustration at right).
■
Manually turn on your VCR,TV, and cable box.
STOP
RECORD
PLAY
REW
PAUSE
SETUP
FWD
VCR CONTROLS
The setup code for the
GI/Jerrold™ CFT2200™ series
cable box is
002
Jerrold™ is a trademark of GIC corp.
Helpful
Hint
Following the above steps allows the remote to control
volume through your cable box.If you would like volume
to be controlled through your TV,perform step 3 before
step 2.If you have a combination TV/VCR,volume will be
controlled only through the cable box.
N
O
T
E
I
N
F
O
for
your
TV
for
your
cable
box
step
1
Press the
[VCR POWER]
button,then the
[SETUP]
button on the remote.
Enter the 3-digit VCR code for your brand of VCR listed in the “VCR codes” chart on the
other side of this manual by pressing the appropriate buttons on the numeric key pad.
Press the
[SETUP]
button again to save the code. The red indicator light at the upper
right-hand corner of your remote will flash 3 times if these steps were followed correctly.
Press the
[VCR POWER]
button again to test the code you‘ve entered. The VCR
should turn ON or OFF each time the
[VCR POWER]
button is pressed. If the VCR
doesn’t turn ON and OFF, repeat this VCR setup procedure with the next code listed in
the “VCR codes” chart.
for
your
VCR
vcr controls
These keys operate standard VCR functions.
Operating Note:
Press the
[RECORD]
button
twice to start recording on your VCR.
numeric keypad
These keys allow you to enter the channel
you want to view.You will also use them
to setup the remote
cable box
function keys
See the chart below for a description
of the key functions
After you find the correct code for each device, write the code on the supplied sticker.
Depending on the configuration
of your cable box, certain
functions listed below may or
may not be functional.
N
O
T
E
Memory Lock
™
is an exclusive technology
that saves the device codes that are
programmed into the remote, even when
the batteries are removed.
MEMORY L
OCK
™
featuring
Cursor Keys
US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.
w w w . u s e l e c t r o n i c s . c o m
