Upright X27-33RT Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 134

background image

Inspection Procedures Codes

(1) Weld cracks, dents and/or rust
(2) Installation
(3) Leaks
(4) Operation
(5) Condition
(6) Tightness
(7) Residue buildup
(8) See placards and decals inspection chart

CHECK

OK

ü

X

BASEFRAME

Structural (1)
Steering cylinders (2,3,4,6)
Steering cylinder fasteners and linkage (2,4)
Tires and wheels (5)
Articulating axles, if so equipped (2,4,5)
Tray side covers (2,5,6)
Torque drive wheel lug nuts 90 - 100 ft. lbs. (2,6)
Torque steer wheel lug nuts 90 - 100 ft. lbs. (2,6)
Right drive motor(s) (3,6)
Left drive motor(s) (3,6)
Drive cut-out
Back-up horn (4)
Guides, rollers and slides (2,4,5)
Parking brake(s) (3,4)
Free wheeling valve (3,4)
Emergency lowering valve (3,4)
Lowering alarm (4)
Battery disconnect switch (4)
Lubrication points
Cords and wire assemblies (2,5,6)
Hydraulic tubes and hoses (3,5)
Decals and placards (2,8)

OUTRIGGERS AND CONTROLS

Right front outrigger (2,3,4)
Left front outrigger (2,3,4)
Right rear outrigger (2,3,4)
Left rear outrigger (2,3,4)
Platform elevated, outrigger controls
DO NOT WORK (4)
Outriggers lowered, platform elevated
DRIVE WILL NOT WORK (4)

SCISSOR ARM ASSEMBLY

Structural (1)
Scissor arm pivot pins (2,5)
Lift cylinders and valves (2,3,4)
Safety bar (2,4,5)
Hydraulic tubes and hoses (3,5)
Wires and electrical cables (2,5)
Decals and placards (2,8)

CHECK

OK

ü

X

BASE CONTROL STATION

Key switch, main power ON - OFF (4)
Selector switch base/platform controls -
BASE CONTROLS SELECTED
PLATFORM CONTROLS DO NOT WORK (4)
Selector switch base/platform controls -
PLATFORM CONTROLS SELECTED
BASE CONTROLS DO NOT WORK (4)
Toggle switch, platform UP - DOWN (4)
Key start switch (4)
Toggle switch, glow plug, timing light
diesel units only (4)
Fuel select switch GAS - LP FUEL (4)
Emergency stop switch (4)
Hour meter (4)
Circuit breaker reset (4)
Lowering alarm (4)
Engine kill alarm (4)
Low oil pressure alarm (4)
High temperature alarm (4)
Lift enable light (4)

PLATFORM

Structural (1)
Guardrails properly installed and fastened (2,5)
Platform entrance chain or gate (2,5)
Wires and electrical cables (2,5)
Decals and placards (2,8)
Correct operators manual in document holder
Roll out platform deck extension (2,4,5,8)

PLATFORM CONTROLS

Drive speed - platform elevated
SLOW DRIVE SPEED ONLY (4)
Drive speed - platform lowered
DRIVES FAST or SLOW (4)
Joystick control -
DRIVE/STEER and PROPORTIONAL LIFT (4)
Toggle type selector switch -
HIGH SPEED/HIGH TORQUE (4)
Toggle type selector switch - LIFT/DRIVE (4)
Low engine oil light (4)
Engine start/kill switch (4)
Lift enable light, if so equipped (4)
Raised platform drive enable light,
if so equipped (4)
Emergency stop button (4)
Joystick interlock switch (4)
Selector switch - ALTERNATOR/MACHINE
Units equipped with optional AC alternator (4)

page 14

Rev D

SR3370 & SR2770 – 13184B

Maintenance Information

■

Preventive inspection maintenance
90 day or 150 hour checklist

OK

OK - No Service Required

Serial Number

✔

Corrective Action Required

X

Corrected, (Record description of corrective action).

«
...
16
17
18
19
20
...
»

Содержание X27-33RT







































































































































Отзывы:

Нет отзывов

Похожие инструкции для X27-33RT

Бренд: BendPak Страницы: 29

Бренд: Titan Lifts Страницы: 30

Бренд: Oshkosh Страницы: 462

Heightrider HR21

Бренд: nifty Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды