Upright X Series Скачать руководство пользователя страница 58

Страница: 58 / 164

Page 4-4

Troubleshooting

4.4 - Measured Voltage at I/O Board

X Series Work Platform

4.4 M

EASURED

OLTAGE

I/O B

OARD

Be sure that both the Platform and Chassis Emergency Stop Switches are pulled out to the ON
position.

All voltages are measured between the component and the B- terminal on the Motor Controller.

CONNE

IN NUM

DESCRIPTION

24 Volts = Lift Mode Active / 0 Volts = Lift Mode Inactive

No Connection

24 Volts = Drive Allowed / 0 Volts = Drive Not Allowed

24 Volts from Lower E-Stop / Lower E-Stop Not Depressed

24 Volts from Upper E-Stop / Lower and Upper E-Stops Not Depressed

24 Volts Out to Interlock Lever when Upper Controls Selected & Upper/Lower E-Stops Not Depressed

No Connection

24 Volts = Drive Forward or Lift Up / 0 Volts = Stop Drive Forward or Lift Up

24 Volts = Drive Reverse or Lift Down / 0 Volts = Stop Reverse Drive or Lift Down

Accelerator Input / 20K Pot / 3.5 Volts to 0 Volts, Minimum to Maximum Speed

24 Volts = Steer Left / 0 Volts = Stop Steer Left

24 Volts = Steer Right / 0 Volts = Stop Steer Right.

Goes to 0 Volts to Activate Depression Mechanism Extend Solenoid / 24 Volts = Solenoid OFF

No Connection

24 Volt Supply for Solenoids

Goes to 0 Volts to Activate Forward Solenoid / 24 Volts = Solenoid OFF

Goes to 0 Volts to Activate Reverse Solenoid / 24 Volts = Solenoid OFF

Goes to 0 Volts to Activate Lift Up Solenoid / 24 Volts = Solenoid OFF

Goes to 0 Volts to Activate Steer Left Solenoid / 24 Volts = Solenoid OFF

Goes to 0 Volts to Activate Steer Right Solenoid / 24 Volts = Solenoid OFF

Goes to 0 Volts to Activate Alarm / 24 Volts = Alarm OFF

24 Volts = Tilt Inactive / 0 Volts = Tilt Active

24 Volt Supply for Alarm, Tilt Sensor, Lift Down and Depression Mechanism Retract Solenoids

24 Volts = Below Height Limit / 0 Volts = Above Height Limit

Goes to 0 Volts to Activate Lift Down Solenoid / 24 Volts = Solenoid OFF

Goes to 0 Volts to Activate Depression Mechanism Solenoid / 24 Volts = Solenoid OFF

24 Volts = High Speed Active / 0 Volts = Low Speed Active

Battery Negative Supply for Tilt Sensor

Goes to 0 Volts to Activate Line Contactor / 24 Volts = Line Contactor OFF

Supplies 24 Volts to Upper Control / Lower Control Switch

24 Volts = Lower Control Mode

Supplies 24 Volts to Ground Lift Switch when in Lower Control Mode

24 Volt Supply Output

Goes to 0 Volts to Activate Hour Meter / 24 Volts = Hour Meter Not Activated

24 Volts = Lift Up from Ground Control / 0 Volts = Lift Up OFF

24 Volts = Lift Down from Ground Control / 0 Volts = Lift Down OFF

24 Volt Supply Input from Battery via Lower E-Stop / Lower E-Stop Not Depressed

24 Volts from Upper Control Switch / 24 Volts = Upper Control Mode

Battery Negative Input to I/O Board

24 Volt Supply for Hour Meter and Line Contactor

24 Volts power to Pin 1 of SC1000 (Key ON Power)

24 Volts = Command Controller to Drive / 0 Volts = Stop Controller Drive

24 Volts = Command Controller to Steer / 0 Volts = Steer OFF

24 Volts = Command Controller to Lift / 0 Volts = Stop Lift

24 Volts = Command Normal Speed / 0 Volts = Command Speed Cutback

24 Volts = Line Contactor OFF / 0 Volts = Line Contactor ON

24 Volts = No Direction Solenoid Allowed / 0 Volts = Direction Solenoid Allowed to Activate

Accelerator 3.5 Volts to 0 Volts / Minimum to Maximum Speed

060571-005

Содержание X Series





































































































































































Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды

Upright X Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание X Series

Отзывы:

Похожие инструкции для X Series

Бренды по названию

Популярные бренды