Upright X Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 164

background image

Page 2-8

Operation and Specifications

2.3 - Operation

X Series Work Platform

A

FTER

U

SE

E

ACH

D

AY

1. Ensure that the platform is fully lowered.

2. Park the machine on a firm, level surface, preferably under cover, secure against vandals,

children, and unauthorized operation.

3. Turn the Key Switch to OFF and remove the key to prevent unauthorized operation.

P

ARKING

B

RAKE

R

ELEASE

Perform the following only when the machine will not operate under its own power and it is neces-
sary to move the machine or when winching onto a trailer to transport.

NOTE:

X31N models have two identical brake adjustment nuts located on both sides of the ladder. The

X20N, X20W, and X26N have only one.

Figure 2-6: Parking Brake Release

The Brake Adjustment/Release
Nut(s) is/are located at the rear of
the machine to the right and/or left
of the ladder.

1. To release the brakes, turn the

nut(s) counterclockwise until
the brakes disengage the
tires.

2. The machine will now roll

when pushed or pulled.

3. To re-engage the brakes, turn

the nut(s) clockwise until the
brakes have fully engaged the
tires.Verify that the brakes
have fully engaged the rear
tires before operating the
machine by testing their abil-
ity to hold the machine on a
22% grade.

REAR

REAR

Parking Brake Release

Parking Brake Release

W A R N I N G

!

!

Never tow faster than 1 ft./sec. (0,3m/sec.)

Never operate the work platform with the parking brakes released. Serious
injury or damage could result.

060571-005

«
...
18
19
20
21
22
...
»

Содержание X Series





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Series

Бренд: stellar labs Страницы: 52

Calc-An-Acre II

Бренд: micro-trak Страницы: 30

Бренд: TradeQuip Страницы: 7

Century 2 NCL10000 Series

Бренд: BraunAbility Страницы: 39

OBID ID ISC.ANT40/30

Бренд: Feig Electronic Страницы: 2

Бренд: Parweld Страницы: 20

NeverFreeze SX-0810-24

Бренд: ThermoSoft Страницы: 5

Бренд: Omega Страницы: 16

Бренд: Mobile Industrial Robots Страницы: 73

Бренд: NEC Display Solutions Страницы: 4

POWER WAVE AC/DC

Бренд: Lincoln Electric Страницы: 48

Hurricane Zephyr HW

Бренд: ITR Страницы: 89

Бренд: Chimera Страницы: 14

Бренд: FISCHER Страницы: 100

Бренд: Riello Страницы: 20

Бренд: Eaton Страницы: 8

Бренд: CMC Страницы: 77

Aeware Advanced in.k600

Бренд: Gecko Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды