Upright X Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 164

background image

Page 2-4

Operation and Specifications

2.3 - Operation

X Series Work Platform

2.3 O

PERATION

Before operating the work platform, ensure that the pre-operation safety inspection has been
completed, and that any deficiencies have been corrected. Never operate a damaged or mal-
functioning machine. The operator must be thoroughly trained on this machine, and must read,
fully understand, and follow this Operator Manual and Scaffold Industry Association’s MANUAL
of RESPONSIBILITIES of ANSI A92.6-1999.

P

LATFORM

E

XTENSION

Figure 2-4: Platform Extension

1. Mount the platform and properly close the

entrance.

2. Depress the foot lever located at the rear of

the platform extension. Push the platform
extension forward until the pin engages the
front stop.

3. To retract the platform extension, depress the

foot lever and pull the platform extension
toward the rear of the machine until the pin
engages the rear stop.

T

RAVEL

WITH

P

LATFORM

L

OWERED

1. Check that the route is clear of obstacles (per-

sons, obstructions, holes, drop-offs, bumps,
and debris), is level, and capable of support-
ing the wheel loads.

2. Turn the Chassis Key Switch to DECK.

3. Pull Chassis Emergency Stop Switch to the ON position.

4. Mount the platform and properly close the entrance.

5. Check clearances above, below and to the sides of the platform.

6. Pull Platform Emergency Stop Switch to the ON position.

7. Turn Lift/Drive Switch to DRIVE.

NOTE:

Turn Lift/Drive Switch to HI (if applicable) for traveling on level ground, or to LOW when extra

torque is required for climbing grades.

8. Engage the Interlock Switch and move the Control Handle to FORWARD or REVERSE to

travel in the desired direction. The speed of the machine will vary depending on how far
from center the Control Handle is moved.

060571-005

«
...
14
15
16
17
18
...
»

Содержание X Series





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Series

Бренд: WAGNER Страницы: 128

Бренд: biodex Страницы: 20

BNI PNT-507-005-Z040

Бренд: Balluff Страницы: 2

Бренд: Dyna-Glo Страницы: 9

Бренд: Ruida Technology Страницы: 35

Бренд: M-system Страницы: 10

SwitchPoint Infinity 3

Бренд: Stryker Страницы: 124

Бренд: Balluff Страницы: 4

Digi-Tig250ACDC

Бренд: CARBONE Страницы: 43

Бренд: NIFTYLIFT Страницы: 46

Бренд: F.F. Group Страницы: 82

Бренд: Revo Страницы: 6

Бренд: Spartus Страницы: 28

Invertig 221 AC/DC

Бренд: HTP Страницы: 28

Бренд: MAHA Страницы: 28

Бренд: MANDREL welder Страницы: 36

Бренд: PVI Страницы: 12

Бренд: btsr Страницы: 129

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды