Uponor Combi Port PRO Скачать руководство пользователя страница 7

Страница: 7 / 36

3.3 Components

Note

The following illustrations show example set-ups for all
units. Individual modules may vary in appearances.

Combi Port Base

G H

CD0000311

Item

Description

Proportional volume control (PM)

Cold water throttle disc

Plate heat exchanger

Sensor pocket heat meter

Cold water meter distance piece

Valve (for thermostatic control of secondary heating)

Equipotential bonding connection

Earthing on site

Zone valve for limiting heating flow to apartment

Heat meter distance piece

Strainer

Draining and filling valve

Connection, ball valve

Combi Port Base TWB

CD0000312

Item

Description

Proportional volume control (PM)

Cold water throttle disc

Plate heat exchanger

Sensor pocket heat meter

Cold water meter distance piece

Thermostatic hot water temperature limiter (TWB)

Valve (for thermostatic control of secondary heating)

Earthing on site

Equipotential bonding connection

Zone valve for limiting heating flow to apartment

Heat meter distance piece

Strainer

Draining and filling valve

Connection, ball valve

Connection description

CD0000305

Item

Description

Cold water to apartment (CW)

Domestic hot water to apartment (DHW)

Cold water from riser (CW)

Heating supply (primary)

Heating return (primary)

Heating supply (secondary)

Heating return (secondary)

Combi Port Base

Installation and operation manual

Содержание Combi Port PRO





































Результаты поиска

Содержание Combi Port PRO

Отзывы:

Похожие инструкции для Combi Port PRO

Бренды по названию

Популярные бренды

Uponor Combi Port PRO, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Combi Port PRO

Отзывы:

Похожие инструкции для Combi Port PRO

Бренды по названию

Популярные бренды