background image

uno. 

Uno International Ltd.  
Stepper Control Board Manual 

 

 

21/21 

Any protocol is specific to one pump only. Using this software you can write the most complex procedures. 
 
 

4.  Warranty 

Uno International Ltd. warrants that each product described herein will be free from defects in materials and 
workmanship for a period of one year from the date of delivery.  
 
The limited warranty is not applicable to: (1) abnormal wear and tear (2) abuse, unreasonable use, improper 
installation, mistreatment, or neglect (3) damage caused by equipment or system with which the product is 
used (4) damage caused by modification or repair not made or authorized by Uno International Ltd., or (5) theft, 
vandalism, fire, water or other peril. Product may not be returned without proper authorisation from Uno 
International Ltd.. Cost of transportation, removal, or reinstallation of the equipment will be paid by the 
purchaser. This warranty and the remedies set forth herein are exclusive and in lieu of all other express or 
implied (including any implied warranties or merchantability or fitness for a general purpose), and no other 
representations or claims shall be binding on or obligate Uno International Ltd. in any way. In no event will Uno 
International Ltd. be liable for any special, incidental, or consequential damages resulting from use or 
malfunction of this product or the equipment or system with which it is used, loss of revenue, or cost of 
replacement of goods. 
 

Содержание Stepper Control Board






















Отзывы: