INSTRUCTION SHEET
543B280/28R
543B290/29R
543B291/291R
Respite Bed 5/0 6/6 6/0
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution:
(1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Headboard
1pc
B
Footboard
1pc
C
Side Rail
2pcs
D
Slat
3pcs
E
Support Leg
3pcs
F
Headboard Post
2pcs
G
Footboard Post
2pcs
H
Short Canopy
2pcs
I
Long Canopy
2pcs
J
Finial
4pcs
Assembly Procedure
: (Please follow the sketches below.)
Step 1:
Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2:
Put the headboard (A) and footboard (B) upright down on a soft and smooth surface to avoid
damage or being scratched. Attach the side rails (C) to the headboard (A) and footboard (B)
with flat washers (3), spring washers (4) and nuts (5) using wrench (6). And attach the
support legs (E) to the slats (D) by hand. Then attach the slats (D) the side rails (C) with
allen head bolt (7) and flat washer (8) using allen wrench (9).
Step 3:
Attach the posts (F, G) to the headboard (A) and footboard (B) by hand. And then connect
the short canopy (H) with Long canopy (I) with bolts (1) using lug wrench (2).
Step 3:
Attach the canopies (H,I) and finial (J) to the posts (F,G) by hand as below shown.
Note:
543290/29R/291/291R have 6 pieces support legs.
Assembly is now complete.
HARDWARE LIST(K)
1
Q'TY
2
LUG WRENCH
3
5/16*19*2MM
1 PC
5/32”*1/2”
4 PCS
6
8 PCS
HARDWARE LIST(K)
Q'TY
70*30*4mm
FLAT WASHER
M12
1 PC
4
8 PCS
5/16"*13*2mm
5
5/16"
8 PCS
7
8
1/4”*3/4"
6 PCS
6 PCS
1/4*19*2MM
9
70*30*4MMMM
1 PCS
BOLT
SPRING WASHER
NUT
WRNCH
ALLEN HEAD BOLT
FLAT WASHER
ALLEN WRENCH
