IMPORTANT SETUP NOTE!
This pertains to all programming steps.
When you are in setup mode, a compo-
nent LED will light for 20 seconds.If you do
not press a button within 20 seconds, the
LED light will turn off and exit setup mode
and you will need to start over.
A. Quick Set-Up Method
STEP1
Turn on the device you want to
program-to program your TV,
turn the TV on.
STEP2
Point the remote at the TV and
press and hold TV key for 3 sec-
onds. While Holding the TV key,
the POWER LED will light off and
on again. Begin to press the
number keys, one at a time,
starting with 1, then 2, 3...0 until
the TV turns off.
STEP3
Release the TV key to save the
code. The POWER LED will blink
twice to confirm the code is
stored.
B. Pre-Programmed 3-Digit Code
Method
STEP1
Turn on the Component you want
to program(TV, DTA).
STEP2
Press the [COMPONENT] button
(TV or DTA) to be programmed
and OK button simultaneously
for 3 seconds. The POWER LED
light will turn on for 20 seconds
indicating the unit is ready to be
programmed.
STEP3
Point the remote control toward
the Component and enter the 3-
digit code number assigned to
your brand.
*Note :
If the 3-digit code number you just
entered is correct, the Component
will turn Off. If it did not turn Off,
continue entering code numbers
listed for that brand until the
Component turns Off.
STEP4
After you’ve entered the correct
code number and the Component
has turned Off, press the [POWER]
button to turn the Component
back On. Now it is time to test the
VOLUME and MUTE buttons for
the TV to make sure they all work.
If any of the functions do not work
as they should, repeat from STEP
3 using the next 3-digit code num-
ber listed for that brand until you
find the best code.
STEP5
Once you have found the correct
3-digit code, save it by pressing
the same [COMPONENT] button
one more time. The POWER LED
light will blink twice to confirm that
the code was successfully stored.
C. Auto-Search Method
STEP1
Turn on the Component you
want to program (TV, DTA).
STEP2
Press the [COMPONENT] button
(TV or DTA) to be programmed
and OK button simultaneously
for 3 seconds. The POWER LED
light will turn on for 20 seconds
indicating the unit is ready to be
programmed.
STEP3
Point the remote toward the
Component and press the [CH
]
or [CH
] button one step at a
time or keep it pressed. The
remote will emit a series of
ON/OFF commands. Release the
[CH
] or [CH
] button as soon
as the Component turns Off.
STEP4
Test functions. (Same as for 3-
Digit Code Programming Method
- Section B). If any of the func-
tions do not work as they should,
repeat from STEP 3 using [CH
]
or [CH
] buttons to find the cor-
rect code.
STEP5
Save the code. (Same as for
3-Digit Code Programming
Method - Section B).
If you wish to store the TV volume
control in DTA mode, use the follow-
ing steps.
STEP1
Press the [DTA] button and
the [OK] button simultane-
ously for 3 seconds.
The [DTA] Component LED
will turn on for 20 seconds.
STEP2
Press the [VOL
] button.
STEP3
Press the [TV] button.
The Component LED will
blink twice to confirm the
programming.
To return to original state:
If you wish to restore the DTA volume
control in DTA mode, repeat the
above steps but press [DTA] in
STEP3
.
F. Memory Lock System
This remote control is designed to
retain programmed memory for 10
years even after batteries are
removed from the remote control.
G. Write your TV Set-up codes
Set-up Code Number :
For additional information about your
remote control, go to www.universal-
remote.com
Now, repeat the Auto-Search Method
for those Components you could
not program earlier with the Pre-
Programmed Method.
D. Finding a Component Button’s
Setup Code Number
If you used the Auto-Search Method
to program a Component, you may
not know what the correct code num-
ber is. Here is a way for you to identi-
fy the code number, so you can
record it for future reference.
STEP1
Press the [COMPONENT] but-
ton (TV or DTA) you want to
verify and the OK button simul-
taneously for 3 seconds. The
POWER LED light will turn on
for 20 seconds.
STEP2
Press the [INFO] button and
count the number of times the
Component LED light blinks.
This number indicates the first
digit of the code, followed by
the second and third, each sep-
arated by a one second pause
when the LED will turn off.
*Note :
10 blinks represents the
number zero.
Example :
One blink, (pause), eight
blinks, (pause) and three
blinks, indicates code
number 183.
E. Programming Volume Control
Volume and Mute control are factory-
programmed to automatically transfer
to the respective Component mode you
select, as follows:
DTA
: TV
T V
: TV
However, you can program the volume
controls (Volume Up, Volume Down
and Mute) from one Component to
operate in another Component.
Button Functions
4
Programming the Remote Control
5
There are three ways you can program your remote:
* Quick Set-Up Method
* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method
The Quick Set-Up Method is a unique new feature that enables the fastest and
easiest set-up by using one-digit codes for up to 10 major brands for each compo-
nent.
The Pre-Programmed Code Method allows you to setup all the buttons at once by
entering 3-digit code numbers that correspond to a particular Component’s manu-
facturer/brand, so it’s the fastest and easiest of the two methods. (Code Tables
are on the backside of this Instruction Sheet.) The Auto-Search Method scans
through all the codes in the remote control, one at a time.
Universal Remote Control, Inc.
www.universalremote.com
OCE-0089A REV 03 (05/26/10)
Operating Instructions For
UR2-DTA
DTA Remote Control
The
UR2-DTA
is designed to
operate the S/A, Pace Micro,
Motorola and IPTV set tops, plus
the majority of TV equipment on
the market as shown below.
DTA :
DTA boxs, IPTV set tops
TV :
Televisions
Introduction
1
Volume Default:
TV volume and mute
through The TV, with the option of con-
trolling volume and mute through the
Cable. Refer to Section
E
For program-
ming the volume and mute through
your Cable.
Operations
3
Replacing Batteries
2
Before you program or operate the
remote control, you must install two new
AA alkaline batteries.
STEP1
Remove the battery compart-
ment cover on the back of your
remote control.
STEP2
Check battery polarity carefully,
and install the batteries as
shown in the illustration below.
STEP3
Replace the battery compart-
ment cover.
