background image

V350-35-R34 Installation Guide

8

Unitronics 

Communication Port 

 

Turn off power before making communications connections. 

Caution

 

Signals are related to the controller’s 0V; the same 0V is used by the power supply. 
Always use the appropriate port adapters. 
The serial port is not isolated. If the controller is used with a non-isolated external 
device, avoid potential voltage that exceeds ± 10V. 

Port 1 is type RJ-11 and may be set to either RS232 or RS485 via jumper as shown below.  
By factory default, the port is set to RS232, termination ON. 

Use RS232 to download programs from a PC, and to communicate with serial devices 
and applications, such as SCADA.   
Use RS485 to create a multi-drop network containing up to 32 devices. 

Pinouts

The pinouts below show the PLC port signals. 
To connect a PC to a port that is set to RS485, remove the RS485 connector, and connect the PC to 
the PLC via the programming cable. Note that this is possible only if flow control signals are not used 
(which is the standard case). 

RS232  

RS485** 

Controller 

Port 

Pin # 

Description 

 

Pin # 

Description 

1* DTR 

signal 

 

1  A 

signal 

(+) 

2

0V reference 

 

(RS232 signal) 

3

TXD signal 

 

(RS232 signal) 

4

RXD signal 

 

(RS232 signal) 

5

0V reference 

 

(RS232 signal) 

6* DSR 

signal 

 

6  B 

signal 

(-) 

 

Pin #1

*Standard programming cables do not provide connection points for pins 1 and 6. 
**When a port is adapted to RS485, Pin 1 (DTR) is used for signal A,  
  and Pin 6 (DSR) signal is used for signal B. 

RS232 to RS485 Jumper Settings

The figure to the right shows the jumper 
factory default settings, RS232, RS485 
termination ON. 
Note that in order: 

To change the communication 
setting to RS485, both 
communication standard jumpers 
must be moved 
To change the RS485 
termination, both termination 
jumpers must be moved 

To access the jumpers, you must open the 
controller according to the instructions 
beginning on page 9. 
 

Содержание Vision OPLC V350-35-R34











Отзывы: