Unitor UPC 1041 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 46

background image

Revision date: 120813

Page 16 of 46

Check the D5 main rectifier.

Verify that the machine is disconnected from the mains supply.

Measure with instrument set to diode test, place the

positive probe

on cable

74

and the

negative probe

on cable

11 , 21 and 31

. Correct value is approx 0.5V this can differ slightly

between instruments. If a short is measured then replace the D5 main rectifier.

Measure with instrument set to diode test, place the

negative

probe on cable

73

and the

positive

probe on cable

11 , 21 and 31

. Correct value is approx 0.5V this can differ slightly

between instruments. If a short is measured then replace the D5 main rectifier.

«
...
14
15
16
17
18
...
»

Содержание UPC 1041















































Отзывы:

Нет отзывов

Похожие инструкции для UPC 1041

Бренд: Yale Страницы: 5

Бренд: EasyPro Страницы: 8

Бренд: Easylift Страницы: 127

Бренд: Vandersteen Audio Страницы: 20

Бренд: RTRMAX Страницы: 14

Бренд: Gemini Страницы: 10

Бренд: M-system Страницы: 9

Бренд: E2S Страницы: 12

Бренд: Icare Страницы: 27

Бренд: Patrol Hawk Страницы: 13

Бренд: 4Ddoors Страницы: 20

Бренд: HURNER Страницы: 69

NVL Vista Series

Бренд: Braun Страницы: 53

Бренд: Peavey Страницы: 4

Бренд: Athena Страницы: 183

Бренд: ROEL Страницы: 28

2CB5-S Replacement Cartridge EV9617-22

Бренд: Everpure Страницы: 2

Security System D7412

Бренд: ADT Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды