United Technologies Carrier Weathermaker 48A2 Скачать руководство пользователя страница 55

Страница: 55 / 208

VFD Heating Minimum Speed (

HT.V.M

) — This is the low

speed setting for units in heating mode. The range is 75 to

100% with the default setting of 75%.
NOTE: Most VFDs have a built-in minimum speed adjustment

which must be configured for 0% when using

Comfort

Link

controls for static pressure control.
VFD Maximum Speed (

SP.MX

) — This is the maximum

speed for the supply fan VFD. This is usually set to 100%

when

CV.FD

= Yes, the range is 33 to 67% with the default set-

ting of 67%.
VFD Fire Speed Override (

SP.FS

) — This is the speed that

the supply fan VFD will use during the pressurization, evacua-

tion and purge fire modes. This is usually set to 100%.
Static Pressure Reset Configuration (

SP.RS

) — This option

is used to configure the static pressure reset function. When

SP.RS

= 0, there is no static pressure reset via an analog input.

If the outdoor air quality sensor is not configured (

Configura-

tion



IAQ



IAQ.CF



OQ.A.C

= 0), then it is possible to use

the outdoor air quality sensor location on the CEM board to

perform static pressure reset via an external 4 to 20 mA input.

Configuring

SP.RS

= 1 provides static pressure reset based

on this CEM 4 to 20 mA input and ranges from 0 to 3 in. wg.

Wire the input to the CEM using TB6-11 and 12. When

SP.RS

= 2, there is static pressure reset based on RAT and defined by

SP.RT

and

SP.LM

. When

SP.RS

= 3, there is static pressure re-

set based on SPT and defined by

SP.RT

and

SP.LM

Setting

SP.RS

to 1, 2 or 3 will give the user the ability to re-

set from 0 to 3 in. wg of static pressure. The reset will apply to

the supply static pressure setpoint. The static pressure reset

function will only act to reduce the static pressure control point.

As an example, the static pressure reset input is measuring

6 mA, and is therefore resetting 2 mA (6 mA – 4 mA) of its

16 mA control range. The 4 to 20 mA range corresponds

directly to the 0 to 3 in. wg of reset. Therefore 2 mA reset is

2/16 * 3 in. wg = 0.375 in. wg of reset. If the static pressure

setpoint (

SP.SP

) = 1.5 in. wg, then the static pressure control

point for the system will be reset to 1.5 – 0.375 = 1.125 in. wg.

When

SP.RS

= 4, the static pressure reset function acts to pro-

vide direct VFD speed control where 4 mA = 0% speed and 20

mA = 100% (

SP.MN

and

SP.MX

will override). Note that

SP.CF

must be set to 1 (VFD Control), prior to configuring

SP.RS

= 4.

Failure to do so could result in damage to ductwork due to over-

pressurization. This is the recommended approach if a third par-

ty wishes to control the variable speed supply fan. In effect, this

represents a speed control signal “pass through” under normal

operating circumstances. The

Comfort

Link control system over-

rides the third party signal for critical operation situations, most

notably smoke and fire control.
Static Pressure Reset Ratio (

SP.RT

) — This option defines

the reset ratio in terms of static pressure versus temperature.

The reset ratio determines how much is the static pressure

reduced for every degree below setpoint for RAT or SPT.
Static Pressure Reset Limit (

SP.LM

) — This option defines

the maximum amount of static pressure reset that is allowed.

This is sometimes called a “clamp.”
NOTE: Resetting static pressure via RAT and SPT is primarily

a constant volume application which utilizes a VFD. The rea-

soning is that there is significant energy savings in slowing

down a supply fan as opposed to running full speed with

supply air reset. Maintaining the supply air setpoint and

slowing down the fan has the additional benefit of working

around dehumidification concerns.
Static Pressure Reset Economizer Position (

SP.EC

) — This

option effectively resets ECONOMIN to fully occupied ventila-

tion position, to account for the drop in static pressure during stat-

ic pressure reset control. The static pressure reset for the calcula-

tion cannot be larger than the supply air static setpoint (

SPSP

The calculation is as follows:
(Static Pressure Reset/

SP.LM

) x (ECONOSPR –

ECONOMIN)

As an example, the static pressure reset limit (

SP.LM

) =

0.75 in. wg. The current static pressure reset is set to 0.5 in. wg.

The settings for ECONOSPR = 50% and ECONOMIN = 20%.

Therefore, the amount to add to the economizer’s

ECONOMIN configuration is: (0.5/0.75) x (50-20) = 20%. In

effect, for the positioning of the economizer, ECONOMIN

would now be replaced by EC 10%.
Static Pressure PID Config (

S.PID

) — Static pressure PID

configuration can be accessed under this heading in the

Con-

figuration



submenu. Under most operating conditions the

control PID factors will not require any adjustment and the

factory defaults should be used. If persistent static pressure

fluctuations are detected, small changes to these factors may

improve performance. Decreasing the factors generally reduces

the responsiveness of the control loop, while increasing the

factors increases its responsiveness. Note the existing settings

before making changes, and seek technical assistance from

Carrier before making significant changes to these factors.

Static Pressure PID Run Rate (

S.PID



SP.TM

) —

This is the

number of seconds between duct static pressure readings taken

by the

Comfort

Link PID routine.

Static Pressure Proportional Gain (

S.PID



SP.P

) —

This is the

proportional gain for the static pressure control PID control loop.

Static Pressure Integral Gain (

S.PID



SP.I

) —

This is the

integral gain for the static pressure control PID control loop.

Static Pressure Derivative Gain (

S.PID



SP.D

) —

This is the

derivative gain for the static pressure control PID control loop.

Static Pressure System Gain

(

S.PID



SP.SG

) — This is the

system gain for the static pressure control PID control loop.
STATIC PRESSURE RESET OPERATION — The

Com-

fort

Link controls support the use of static pressure reset. The

Linkage Master terminal monitors the primary air damper posi-

tion of all the terminals in the system (done through LINKAGE

with the new ComfortID™ air terminals).

The Linkage Master then calculates the amount of supply

static pressure reduction necessary to cause the most open

damper in the system to open more than the minimum value

(60%) but not more than the maximum value (90% or negligi-

ble static pressure drop). This is a dynamic calculation, which

occurs every two minutes whenever the system is operating.

The calculation ensures that the supply static pressure is always

enough to supply the required airflow at the worst case termi-

nal but never more than necessary, so that the primary air

dampers do not have to operate with an excessive pressure

drop (more than required to maintain the airflow setpoint of

each individual terminal in the system).

As the system operates, if the most open damper opens

more than 90%, the system recalculates the pressure reduction

variable and the value is reduced. Because the reset value is

subtracted from the controlling setpoint at the equipment, the

pressure setpoint increases and the primary-air dampers close a

little (to less than 90%). If the most open damper closes to less

than 60%, the system recalculates the pressure reduction vari-

able and the value is increased. This results in a decrease in the

controlling setpoint at the equipment, which causes the

primary-air dampers to open a little more (to greater than 60%).

The rooftop unit has the static pressure setpoint pro-

grammed into the CCN control. This is the maximum setpoint

that could ever be achieved under any condition. To simplify

the installation and commissioning process for the field, this

system control is designed so that the installer only needs to en-

ter a maximum duct design pressure or maximum equipment

pressure, whichever is less. There is no longer a need to calcu-

late the worst case pressure drop at design conditions and then

hope that some intermediate condition does not require a

Содержание Carrier Weathermaker 48A2

















































































































































































































Результаты поиска

Содержание Carrier Weathermaker 48A2

Отзывы:

Похожие инструкции для Carrier Weathermaker 48A2

Бренды по названию

Популярные бренды

United Technologies Carrier Weathermaker 48A2, Управление, пуск, эксплуатация, обслуживание и устранение неисправностей.

Результаты поиска

Содержание Carrier Weathermaker 48A2

Отзывы:

Похожие инструкции для Carrier Weathermaker 48A2

Бренды по названию

Популярные бренды