background image

 

 

Copyright 2014 unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of unitech Electronics Co., Ltd. 

1.  This Transmitter must not be co-located or operating in conjunction with any other antenna 

or transmitter. 

2.  This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled 

environment. To maintain compliance with FCC RF exposure requirements, avoid direct 
contact to the transmitting antenna during transmitting. 

3.  Any changes or modifications (including the antennas) made to this device that are not 

expressly approved by the manufacturer may void the user’s authority to operate the 
equipment. 

 

FCC Label Statement 

This device complies with part 15 of the FCC rules. Operation is subject to the following two 
conditions: 
1.  This device may not cause harmful interference, and 
2.  This device must accept any interference received, including interference that may cause 

undesired operation. 

 

RF Radiation Exposure Statement 

For body contact during operation, this phone has been tested and meets FCC RF exposure 
guidelines when used with an accessory that contains no metal and that positions the handset 
a minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with 
FCC RF exposure guidelines. 
 

Canadian Compliance Statement 

This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing 
Equipment Regulations. 
 
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material 
broilleur du Canada. 
 

European Conformity Statement 

Declaration of Conformity with regards to the R&TTE 1999/5/EC and EMC 89/336/ EEC 
directives. 
 

RoHS Statement 

This device conforms to RoHS (Reduction Of Hazardous 
Substances) European Union regulations that set maximum 
concentration limits on hazardous materials used in electrical and 
electronic equipment. 

Содержание MS832








































































































































Отзывы: