background image

66339-BIM-C-0206

4

Unitary Products Group

GENERAL

The LL-15 and LL-20 evaporator units are designed for
use with the LL-15 and LL-20 Series condensing units.

Each unit consists of a coil section and a blower sec-
tion that are factory assembled and shipped. As shown
in arrangement 1 of figure 5, these sections may be
rearranged in the field for other air discharge patterns.
See figures 5, 6 and 7.

NOTES, CAUTIONS AND WARNINGS

Installer should pay particular attention to the words:

NOTE

CAUTION

 and 

WARNING

. Notes are intended

to clarify or make installation easier. Cautions are given
to prevent equipment damage. Warnings are given to
alert installer that personal injury and/or equipment

damage may result if installation procedure is not han-
dled properly.

REPLACEMENT PARTS

Refer to parts manual for complete listing of replace-
ment parts on this equipment. The above forms and all
other forms referenced on this instruction may be
ordered from;

Standard Register
Telephone: 877-318-9675
Toll Free Fax:  877-379-7920

INSPECTION

As soon as a unit is received, it should be inspected for
possible damage during transit. If damage is evident,
the extent of the damage should be noted on the car-
rier’s freight bill. A separate request for inspection by
the carrier’s agent should be made in writing. 

TABLE 1:  PHYSICAL DATA

DESCRIPTION

MODEL

LL-15

LL-20

EVAPORATOR COIL

Rows Deep X Rows High
Finned Length
Face Area, Feet
Tube (copper) OD, Inches
Fins (aluminum) per 1 inch

3 x 32

83

18.4

3/8

13

3 x 40

81

22.5

3/8

16

Piping Connections, Inches

Liquid, Inches

5/8

5/8

Suction, Inches

1 1/8

1 3/8

CENTRIFUGAL BLOWERS (2 

PER UNIT)

Diameter X Width, Inches (Forward Curved)

15 X 12

18 X 18

FILTERS (THROWAWAY)

Size and Quantity Per Model, 
Inches

16 X 25 X 2
20 X 20 X 2
20 X 24 X 2
20 X 25 X 2
25 X 25 X 2

-

4

-

4

-

-
-
-

10

-

Total Face Area, Feet

26.7

34.7

OPERATING CHARGE

(LBS 4-22)

System 1
System 2

15.0
15.0

17.0
17.0

COMPONENT WEIGHT

Basic Unit (Less Motor & Drives)
Shipping Weight (lbs)
Operating Weight (lbs)

720
720
830

990
990

1115

Accessories

Hot Water Coil
Steam Coil
Supply Air Plenum
Return Air Grille

165
175
185

25

225
210
N/A
N/A

Blower Motor (1750 RPM)
(Field Installed)

120 (5 hp)

47 (3 hp)

120 (5 hp)

Содержание LL-15





















Отзывы: