Unipulse TM700 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 91

background image

29

5

　

SETTING OF FUNCTIONS

29

SE

TT

IN

G

O

F

FU

N

C

TI

O

N

S

Chapter

5

5-2.

Moving Average Filter (D. Filter)

The digital filter is a function for reducing drifts of the indicated value by means of a moving
average of data converted from analog to digital. With an increase in the number of filterings, the
indicated value becomes more stable, but the response to inputs becomes slower.
Torque and rotation speed can be individually set.

≪

Setting value

≫

OFF, 2 to 999 [times]

How to set

5-3.

Analog Filter (A. LPF)

A low-pass filter is provided for filtering input signals from the sensor and canceling noise
components.
With an increase in the cut-off frequency, the response becomes faster, but noise components may
be indicated.

≪

Setting value

≫

10, 30, 100, 300, 1k, 3k, 10k, 30k [Hz]

How to set

5-4.

Display Filter

This is a function to display the values for torque, rotation speed and power in a way that is easy to
see by averaging the display values. Only the displayed values are averaged. The data stored inside
the TM700 (graphs, hold) are not averaged.

≪

Setting value

≫

OFF, L(0.5s), M(1.0s), H(2.0s)

How to set

5-5.

Backlight

This function changes the brightness of the backlight when touch screen has not been used for
certain period of time.
The ON time (lighting time of the backlight) and the low time (bright

→

dark switching time of the

backlight) are set up.
When you use it in the state which a display is always in sight, set the ON time to 0 minutes.
When you want the backlight always bright, set 0 minutes for both the ON time and the low time.
The backlight is turned bright by touching the panel when the backlight is turned off or it is dark.

SET.

Operation

Page 1

→

→

System Setting

→

SET.

Operation

Page 1

→

→

System Setting

→

SET.

Operation

Page 1

→

→

System Setting

→

«
...
36
37
38
39
40
...
»

Содержание TM700




























































































Отзывы:

Нет отзывов

Похожие инструкции для TM700

SyncMaster S24B750V

Бренд: Samsung Страницы: 98

Бренд: Aspect Страницы: 100

Бренд: TRANSTEK Страницы: 19

e!DISPLAY 7300T

Бренд: WAGO Страницы: 104

Caneo 43 Hygienic Series

Бренд: Captron Страницы: 14

Бренд: Dynascan Страницы: 28

Бренд: switel Страницы: 1

Бренд: FDS Страницы: 25

Бренд: Hisense Страницы: 2

Бренд: AOC Страницы: 48

Бренд: AOC Страницы: 26

Бренд: Daewoo Страницы: 11

Бренд: AOS Страницы: 54

Бренд: Marshall Electronics Страницы: 22

SyncMaster P1980ER

Бренд: Samsung Страницы: 47

SyncMaster PX2370

Бренд: Samsung Страницы: 47

Бренд: Qualitrol Страницы: 189

Бренд: Westinghouse Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды