Unipulse TM201 Скачать руководство пользователя страница 38

Страница: 38 / 58

Calibration

Calibr

Chapter

4-3.

Procedures of equivalent input calibration

and actual load calibration (torque)

Equivalent input calibration and actual load calibration are performed in the following procedures,
and check "Detail" to display detail items.

Calibration setting protection that prevents calibration
is turned OFF ("Management" tab).

The unit is set according to UTM

Ⅱ

used.

Minimum value of the digital change desired is set.
(Optional if there is no change.)

Calibration setting is written to the TM201.

UTM

Ⅱ

is set to unloaded condition (where no torque

load is being applied to UTM

Ⅱ

) and the zero point is

registered.

Equivalent input calibration

Rated output value and rated capacity value of UTM

Ⅱ

are registered.

Actual load calibration

The known torque load is applied to UTM

Ⅱ

and the

torque is registered.

Calibration setting protection is turned ON to avoid
operational errors ("Management" tab).

(1) Release of calibration setting protection

Calibration setting protection is set to OFF.
Only this setting is performed in the "Management" tab.

OFF

Setting values are rewritable.

Setting values are not rewritable.

(7)
Calibration setting protection

(6) a.
Equivalent

(6) b.
Actual load

... Be sure to perform the setting.

(4)
Calibration setting PC

→

TM201

(5)
Zero calibration

(2)
Unit (torque)

input calibration

calibration

(1)
Calibration setting protection

(3)
Min. scale division (torque)

Содержание TM201


























































Результаты поиска

Содержание TM201

Отзывы:

Похожие инструкции для TM201

Бренды по названию

Популярные бренды

Unipulse TM201, Руководство по эксплуатации

Результаты поиска

Содержание TM201

Отзывы:

Похожие инструкции для TM201

Бренды по названию

Популярные бренды