Unipulse M525B Скачать руководство пользователя страница 71

Страница: 71 / 85

ADVANCED USE

ADVANCE

D USE

Chapter

6-4.

Delete Print

Use if you want to delete printed data (when you do not want to add the data to subtotals/grand
totals). Only one piece of the last printed data can be deleted.
Press (DEL)

→

(ENT) in the print mode, and the data is deleted.

Example of printing

EFGHI

119kg

EFGHI

113kg

EFGHI

81kg-

EFGHI

81kg

EFGHI

96kg

EFGHI

111kg

EFGHI

100kg

------------------------
GT　　　　　　　　 539kg
COUNT               5
CODE           EFGHI
DATE   2000/07/04 02:36

--- GRAND TOTAL Ach ---

Data you want to delete

GT (grand total)

The previously printed data i
reprinted as it is marked with “-
indicating deletion, and is delete
from the grand total/sub total data.

The data that can be deleted is only the previously printed data.

Can be deleted

Cannot be deleted

Current value

EFGHI

119kg

EFGHI

81kg

EFGHI

96kg

EFGHI

111kg

EFGHI

100kg

Point

- Delete print cannot be performed twice or more successively.

- In the case of double printing, delete print can be performed only for Bch.

Point

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды