Unipulse M525B Скачать руководство пользователя страница 55

Страница: 55 / 85

ADVANCED USE

ADVANCE

D USE

Chapter

6-1.

Classification by Code Name and Code Table

The M252B can total sub totals and grand totals on the basis of code names assigned to print data.
Up to 32 code names can be registered for each ch.

■

Code Name Registration Performance with Front Panel Keys

Input code names by using numeral keys from

(1) to

(

0), and

(-(ST)),

(SP(GT)),

(DEL) keys. Since each numerical key is assigned approx. 10 characters,

press the key until a desired character is displayed results. (This is designateed a key group.) For the
list of characters assigned to each group, see the appendix "8-5.Character Input Table" on page 72.

- For inputting a character in the same group successively, press

(DEL) once to move

the virtual cursor one character ahead.

- For inputting a character in a different group, input it successively. It is not necessary to press

(DEL).

Maximum number of
code names

32 code names for each ch

Method of registration

- A registration waiting state is developed by inputting with front panel keys

and pressing

(A)

→

(ENT)

(

(B)

→

(ENT) on Bch).

- Input through the RS-232C. (page 43)

Input format

###### (6 digits at the maximum)

Usable characters

umbers, English letters,

katakana

, synbols (-, *, /, space)

Code name
designation method

Front panel keys, RS-232C, BCD input

ADVANCED USE

A B C D E
W X Y Z A
N O P Q R

Registered code names

…

Up to 32 code names

Measuring

Totaling

It is possible to total

Measuring

Totaling

Measuring

Totaling

for each ch

on a code-by-code basis.

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды