Unipulse M525B Скачать руководство пользователя страница 53

Страница: 53 / 85

OPTION

OPTION

Chapter

Details of settings

MODE 0 (M250 mode)

Echo-back is performed with respect to all received commands. Echo-back is also
performed even when the command is invalid (for example, when a code name is received
even though it is set so that code names are to be input with front panel keys)

MODE 1 (M252 mode)

Information regarding whether or not a command has been executed is returned as it is
added to the header with respect to all received commands.

5-5.

Communications Format

The M252B receives all data through the RS-232C as character strings consisting of ASCII
characters. For data and command formats, see below.

Data
(without automatic print)

Data
(automatic print)

O K

Received command CR LF

The received command has been executed.

The received command is invalid.

N G :

Received command CR LF

0 ± 9

9 .

9 CR LF

Command

Sign

5 digits

Terminator

* If no decimal point is included, 0 is added to the uppermost digit.

decimal point

1 ± 0

9 .

9 CR LF

If the setting of "Automatic Print ON/OFF" of M252B is
OFF, no printing will be performed.
See "08 : Automatic Print ON/OFF" (page 26) for details.

Command

Sign

5 digits

Terminator

* If no decimal point is included, 0 is added to the uppermost digit.

decimal point

Attention

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды