Unipulse M525B Скачать руководство пользователя страница 40

Страница: 40 / 85

FOR GREATER USE OF THE PRINTER

FOR GREATER USE OF THE PRINTER

Chapter

Set the target value and range (width from the target value) necessary to work out statistical data
and the histogram.

Example of setting -Setting the target value at 100 and the range at 20-

Example of noprinting -Setting the target value at 80000 and the range at 19999-

Name of setting

13,15: Histogram Target Value Ach/Bch
14,16: Histogram Range Ach/Bch

Input range

Histogram target value

～±

99999 (initial value: +00000)

Histogram range

～

99998 (initial value: 99998)

Setting conditions

(Upper limit) = (Target value) + (Range)

≦

+99998

(Lower limit) = (Target value) - (Range)

≧

-99998

Explanation of setting

- If data exceeding the range is input, U (upper limit exceeded) or

L (lower limit exceeded) is added to the print data.

- For switching the sign during input, use the

(- (hyphen)] key.

- Input a setting value excluding a decimal point.

Example

）

100.0

→

1000

- The range between the upper limit and lower limit are divided into nine equal

parts to produce histogram ranks.

- The numbers of pieces of data exceeding the upper limit and lower limit are

counted as H OVER TIMES and L OVER TIMES, respectively.

- If any data exceeds the upper limit or lower limit at Print-Every time, a

range-over symbol is printed on the right-hand side of the data.
Data

＞

Upper limit

　⇒　

’U’

Data

＜

Lower limit

　⇒　

’L’

Caution

- Since addition of U and L covers all print data during printing, if the

histogram and diagram are not used, use maximum value (initial value) and
the target value of zero (0) (initial vlaue) as the range.

- The target value can be set only in a condition that U and L can be printed.

Before setting the target value, change the range value.

- If any target value is input not meeting the conditions, “Error” will be

printed, and then an automatic movement will be made to the range setting of
the corresponding ch.
Change the range setting value, and then set the target value again.

These setting items also
serve as the

■

Range Over

(U/L)" on page 61

setting

13,15: Histogram Target Value Ach/Bch

14,16: Histogram Range Ach/Bch

100

120

Lower

Target

Upper

L print

55.0kgL etc

U print

150.0kgU etc

limit

value

limit

60001

80000

99999

L print

60000 kgL etc

No U print

More than 99999

cannot be printed.

(

)

Lower

Target

Upper

limit

value

limit

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды