Unipulse M525B Скачать руководство пользователя страница 18

Страница: 18 / 85

PRINTER PREPARATIONS

PRINTER PREPARAT

IONS

Chapter

2-3.

Protective Ground Connection

The grounding terminal is for prevention of electric shocks and failures caused by static electricity.
Use an approx. 0.75mm

thick wire, and be sure to ground

2-4.

Installing Roll Paper

No roll paper has been installed at the time of delivery. Referring to the following procedures,
install roll paper.

Push the center of the push panel with your finger until you hear it click.
The push panel pops out forward. And draw out the push panel.

Insert the roll paper installing bar into roll paper.
Direct the paper winding direction as shown in
the illustration, and set it to the bearing.

WARNING

- Connect with no power applied because it may cause an electric shock.

- The attached AC cable is designed for domestic use in Japan, and its rating is 125V

AC, 10A. For use at voltages exceeding the rating and for overseas use, have a
separate AC cable prepared.

- Since the M252B has no power switch, install a breaker.

- Be sure to ground the protective ground terminal to prevent electric shocks and

injury by static electricity.
(There is continuity between the casing and protective ground terminal.)
Do not use other screws than those installed to the body.

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды