Unipulse F320 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 129

background image

11.D/A CONVERTER

91

11. D/A CONVERTER

11-1. Voltage Output (DAV Option)

This converter is used to obtain an analog output which is linked with the
indicated value of the F320.
The range of the analog output is from -10 to +10V.
An analog output from 0V to ±10V can be obtained with respect to any digital
values set by the D/A zero setting and the D/A full scale setting functions.
The output circuit and the main circuit are isolated.

Voltage output:

-10 to 10V (load resistance; 2k

Ω

or more)

D/A conversion speed:

2000 times/sec.

Resolution:

1/10000

Over range:

-11.0 to +11.0V

Zero adjustment range: Approx. -1.0 to +1.0V (at the time of zero output)
Gain adjustment range: Approx. 9.5 to 10.5V (at the time of full scale output)
Zero drift:

Within 0.6mV/

℃

Gain drift:

Within 50ppm/

℃

Non-linearityv

Within 0.05%FS
* Not including the drift of the analog input section

Output connector:

Screw type terminal block (two-pole)

㨆㧱㧾㧻㧳㧭㧵㧺

㧗

Voltage output terminals

Terminals for obtaining voltage signal.
“+” is for signal, and “-” is for ground.
0 to ±10V can be obtained.

+ -

Gain adjustment
trimmer

Trimmer to adjust so
that the indication
becomes as registered
by the D/A full scale
setting function.
The gain adjustment
range is approx. 9.5 to
10.5V (at the time of
full scale output).

Zero adjustment trimmer

Trimmer to adjust so that the voltage output becomes
zero when the indication is as registered by the D/A
zero setting function.
The zero adjustment range is approx. -1.0 to +1.0V
(at the time of zero output).

«
...
103
104
105
106
107
...
»

Содержание F320


































































































































Отзывы:

Нет отзывов

Похожие инструкции для F320

Бренд: ECC X-RAY Страницы: 14

Бренд: jenway Страницы: 20

Бренд: Keithley Страницы: 48

Бренд: OHAUS Страницы: 52

Бренд: Raymarine Страницы: 42

Wind Monitor Series

Бренд: Campbell Страницы: 38

Бренд: Favero Electronics Страницы: 12

Бренд: Det-Tronics Страницы: 18

Бренд: Armstrong Monitoring Corporation Страницы: 12

Бренд: Veeco Страницы: 349

Бренд: GrainPro Страницы: 7

Бренд: Caen Страницы: 50

Бренд: Vanguard Instruments Company Страницы: 111

CHEM2000-UV-VIS

Бренд: Ocean Optics Страницы: 42

Бренд: Tektronix Страницы: 30

FTCI-3/4D15A4P-2LUX-H1141

Бренд: turck Страницы: 2

Бренд: Vaisala Страницы: 2

Бренд: SKF Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды