manualshive.com logo in svg

Unigas R91 VS Series, Руководство по установке, использованию и обслуживанию, Страница: 18 / 60

Поделиться
Скачать
Unigas R91 VS Series Скачать руководство пользователя страница 18

18

Pressure adjusting range

The pressure adjusting range, upstream the gas valves group, changes according to the spring provided with the valve group.

Keys

Siemens VGD valves with SKP actuator

Once the train is installed, connect electrically all its elements: gas valves group, pressure

switches, gas proving system. 

ADJUSTMENTS

 Siemens SKP actuator 

ATTENTION:

 once the gas train is mounted according to the diagram on Fig. 11, the gas proving test mus be perfor-

med, according to the procedure set by the laws in force.

ATTENTION:

 before starting the burner up, be sure that the manual cutoff valves are open and check that the pres-

sure upstream the gas train complies the value quoted on paragraph “Technical specifications”. Be sure that the 
mains switch is closed.

.

ATTENTION:

 During commissioning operations, do not  let the burner operate with insufficient air flow (danger of formation

of carbon monoxide); if this should happen, make the gas decrease slowly until the normal combustion values are achieved.

WARNING: NEVER LOOSE THE SEALED SCREWS! OTHERWISE, THE DEVICE WARRANTY WILL BE IMMEDIA-
TELY INVALIDATE!

IMPORTANT! the combustion air excess must be adjusted according to the  in the following chart:

Recommended combustion parameters  

Fuel 

Recommended (%) CO

2

  

Recommended (%) O

2

 

Natural gas

9 ÷ 10 

3  ÷ 4.8

2

1

1 spring
2 cap

:

Performance range (mbar)

0 - 22

15 - 120

100 - 250

Spring colour

neutral

yellow

red

TTENZIONE

Содержание R91 VS Series





























































Отзывы:

Нет отзывов