Unifire SUPERVISOR I Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 22

Unifire SUPERVISOR I Скачать руководство пользователя страница 14

0014_Installation_Operation_Manual

Draft

[email protected]

Page 14 of 22

Copyright 2017 Unifire

7.1

Fuses

Fuses are provided on connections X808, X809, X810, X811 and X800. Fuses are located on the
underside of the field IO board.

Connection

Fuse

Rating

X808

F802

2.5A 300V

X809

F803

2.5A 300V

X810

F804

2.5A 300V

X811

F805

2.5A 300V

X800

F801

10A 300V

Integrity of fuses can be checked with a multi-meter without removing the boards from the enclosure.

Figure 5 - Fuse Test Points

To replace fuses it is recommended that the electronics assembly is removed from the enclosure in the
manner described in the preceding section.

Once removed, release the field IO board from the main board by removing the 4 screws and PCB
standoffs located in the corners of the board. Carefully rotate the field IO board forwards to access the
fuses. Replace with radial board mount fuses of equivalent rating. Reinstall the electronics assembly
before powering up.

Fuse Test Points

«
...
12
13
14
15
16
...
»

Содержание SUPERVISOR I























Отзывы:

Нет отзывов