Unical AIREX 150 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 52

background image

Installation instructions

35

5.1 - ELECTRICAL CONNECTIONS

General warnings

The electrical safety of the appliance is guaranteed only when
it has been properly connected to an efficient earthing system
carried out as intended by safety standards in force: pipes of
the gas, water and heating systems are absolutely unsuitable
as earthing electrodes.

It is necessary to verify this fundamental safety requirement.
If in doubt, have the electric system carefully checked by
professionally qualified personnel as the manufacturer is not
liable for damage caused by failure to provide an earthing
system.

Have professionally qualified personnel check that the electric
system is adequate for the maximum power absorbed by the
appliance, indicated on the data plate. Make sure in particular
that the cross-section of the cables is suitable for the power
absorbed by the appliance.

Adapters, multiple sockets and/or extension cords cannot be
used to power the appliance.

Use of any type of component using electric energy requires the
observance of some fundamental rules, such as:
• Do not touch the appliance with wet and/or moist parts of

the body and/or in bare feet.

• Do not pull the electric cables.
• Do not leave the appliance exposed to atmospheric agents

(rain, sun, etc.) unless expressly designed.

• Do not allow children or unskilled persons to use the
appliance.

230V electric power supply connection

The electric connections are illustrated in the section
“INDICATIVE HYDRAULIC AND ELECTRIC DIAGRAMS” (chap.
4 page 23).

Boiler installation requires connection to a 230 V - 50 Hz electric
mains.
This connection must performed up to standard as intended by
current IEC regulations.

Danger!
Only a qualified technician may perform the
electrical installation.
Before performing connections or any type of
operation on electrical parts, always
disconnect electrical power and make sure
that it cannot be reconnected accidentally.

Remember that a bipolar switch must be installed

on the boiler power line with over 3 mm between contacts, easy
to access, making maintenance quick and safe.

The power cable must be replaced by authorised technical per-

sonnel. Failure to comply with the above can
jeopardise the safety of the appliance.

Attention!

- Before opening the panel board, move the main switch
to “0”!
- Do not connect loads to the panel board which on a whole
absorb more than 4A!

Use

This panel board must be used to operate
a boiler intended to heat water at a
temperature which does not exceed the

boiling point when installed.

«
...
33
34
35
36
37
...
»

Содержание AIREX 150





















































Отзывы:

Нет отзывов

Похожие инструкции для AIREX 150

Бренд: Radiant Страницы: 60

Бренд: watersave Страницы: 16

Бренд: Kospel Страницы: 28

Бренд: Camus Hydronics Страницы: 90

Бренд: Cerbos Страницы: 38

Бренд: IDEAL Страницы: 8

Бренд: Ataq Страницы: 16

Logano plus GB102

Бренд: Buderus Страницы: 12

Бренд: STIEBEL ELTRON Страницы: 16

ATLAS D ECO 34 COND SI UNIT

Бренд: Ferroli Страницы: 112

Бренд: Ferroli Страницы: 24

Бренд: Viessmann Страницы: 168

Бренд: Vaillant Страницы: 56

VUW 246/5-3 (H-GB)

Бренд: Vaillant Страницы: 60

Бренд: Rinnai Страницы: 160

Бренд: KyungDong Страницы: 53

Бренд: Bartscher Страницы: 19

Бренд: Electro Industries Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды