UNI-T UPO1000CS Series Скачать руководство пользователя

Страница: 87 / 99

During the operation, when the voltage value of source channel is greater than the threshold

value, it is d

etermined as logic “1”, otherwise it is logic “0”. Turn waveform to the binary system

and then perform the logical operation. Four types logical operation as shown in Table 14-1.

Table 14-1

Source 1

Source 2

AND

XOR

Source1

NOT

(2) Inverse

Inverse can select on or off. ON

：

Invert the waveform of the logical operation.

(3) Threshold 1

Adjusting the Multipurpose knob to change the value of Threshold 1. When the voltage value of the
source channel is greater than the value of Threshold 1, it is identified as logic “1”, otherwise it is
logic “0”.

(4) Threshold 2

Adjusting the Multipurpose knob to change the value of Threshold 2. When the voltage value of the

source channel is greater tha

n the value of Threshold 2, it is identified as logic “1”, otherwise it is

logic “0”.

14.4 Digital Filter

(1) Digital Type

a. Low pass

：

Only signal with the source frequency lower than the current frequency upper limit

are allowed to pass.

b. High pass

：

Only signal with the frequency higher than the current frequency lower limit are

allowed to pass.

Band pass

：

Only signal with the frequency higher than the current frequency lower limit and

lower than the current frequency upper limit are allowed to pass.

d. Band elimination

：

Only signal with the frequency lower than the current frequency lower limit or

higher than the current frequency upper limit are allowed to pass.

(2) The lower limit of frequency

Adjusting the Multipurpose knob to change the value of the lower limit of frequency. When in low

pass, the lower limit of frequency is invalid and the menu is hidden.

(3) The upper limit of frequency

Adjusting the Multipurpose knob to change the value of the high limit of frequency. When in high

pass, the high limit of frequency is invalid and the menu is hidden.

Note

：

The setting range of the upper/lower limit of frequency is related with the current horizontal time

base.

Содержание UPO1000CS Series




































































































Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды

UNI-T UPO1000CS Series, Руководство пользователя

Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды