Unex VTX-301 Скачать руководство пользователя

Страница: 5 / 11

Doc. No: Unex-HDG-20-001

5/11

A printed version of this document is an uncontrolled copy

•

Consult the dealer or an experienced radio/ TV technician for help.

CAUTION:

Any changes or modiﬁcations not expressly approved by the grantee of this device

could void the user’s authority to operate the equipment.

4.4. Modular approval RF Exposure

This equipment must be installed and operated in accordance with provided

instructions and the antenna(s) used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be co-located or

operating in conjunction with any other antenna or transmitter. End-users and installers

must be provide with antenna installation instructions and consider removing the no-

collocation statement.

4.5. Labelling Requirements for the Host device

The host device shall be properly labelled to identify the modules within the host device.

The certification label of the module shall be clearly visible at all times when installed in the

host device, otherwise the host device must be labelled to display the FCC ID and IC of the

module, preceded by the words "Contains transmitter module", or the word "Contains", or

similar wording expressing the same meaning, as follows:

Contains FCC ID: NUK-VTX3012

Содержание VTX-301











