Ulvac RFS-13100F Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 74

Ulvac RFS-13100F Скачать руководство пользователя страница 29

RF Power Supply and Matching Box

4. Functions

21

4-1-3. Measurement display

Item

Display value

Comments

FWD

Traveling wave power

Traveling wave power (Pf)

REF

Reflected wave power

Reflected wave power (Pr)

VDC

VDC voltage

Voltage at the matching box's output terminal

VPP

VPP voltage

Voltage at the matching box's output terminal

4-1-4. Protective functions

In the situations below, RF output drops or is shut off (automatic recovery) and RF output stops after
the set amount of time or the set number of times.

Display

Contents

Action

FWD

Controls traveling wave power if traveling wave power exceeds rated output.

RF droop

REF

Controls reflected wave power if reflected wave power exceeds rated output.

RF droop

Traveling wave power is shut off when the above continues for 30 seconds or
more.

RF shut
off

OC

Controls traveling wave power if the RF amplifier's current exceeds the rated
value.

RF droop

OV

Controls traveling wave power if the RF amplifier's applied voltage exceeds
the rated value.

RF droop

VPP

Controls traveling wave power if the matching box's output terminal voltage
exceeds the rated value.

RF droop

ARC

Shuts off traveling wave power if the reflected wave power momentarily
exceeds the rated value,then after pausing for 10 ms, automatically recovers.

RF shut
off

INTLOCK

Stops traveling wave power when the external interlock operates.

RF OFF

ALARM

Stops traveling wave power for overheating, when the fan air volume
decreases, cooling water volume decreases,RF amplifier output is
unbalanced, when the cover is open, when the main fuse is blown, and when
the DC portion has malfunctioned.

RF OFF

When a malfunction or abnormality in Table 4-4 occurs, a buzzer will sound and RF output stops.
ALARM on the control panel also illuminates in red, an error message is displayed on the screen, and
the monitor signal is externally output.
This situation will continue until the problem is resolved and the RESET key (RF OFF) or RESET signal
is input. The system can be restarted with the RF ON signal after resetting.

Table 4-2 RF power supply measurement display list

Table 4-3 RF power supply protective functions list

«
...
27
28
29
30
31
...
»

Содержание RFS-13100F











































































Отзывы:

Нет отзывов