background image

 

23 

7. In Conclusion 

Please contact the manufacturer’s sales division if you have any questions. 
 

 

 

 

Warranty 

 

(1)  The  warranty  for  this  pump  (this  equipment)  extends  for  a  period  of  one  year  from  the  date  of 

shipment. 

(2) Any malfunctions or defects which occur under normal usage conditions during the warranty period 

will be repaired free of charge. 

Note, the warranty stated here is an individual warranty covering the pump. In addition, the scope of 

the warranty coverage concerning repairs is limited to the repair and/or replacement of parts. 

Normal usage conditions refer to the following: 

a) Ambient temperature and humidity during operation: 7 - 40

°

C, below 85% RH 

b) Operation in accordance with the user manual 

(3) Repair fees will incur during the warranty period for the following cases: 

a) Malfunctions due to a natural disaster or fire. 

b)  Malfunctions  caused  by  special  atmospheric  conditions,  such  as  salt  damage,  inflammable  gas, 

corrosive gas, radiation or pollution. 

c)  Malfunctions  caused  by  usage  conditions  that  differ  from  those  stated  in  the  user  manual 

(performance specifications, maintenance and inspection, etc.). 

d)  Malfunctions  caused  by  modifications  or  repairs  carried  out  by  a  party  other  than  the 

manufacturer, or by a service company not approved by the manufacturer. 

e) Malfunctions caused by noise (electric disturbance). 

f) Malfunctions that occur when not using a rated power supply. 

g)  Malfunctions  that  occur  when  there  is  an  abnormal  rise  in  internal  pressure  due  to  the  pump 

exhaust outlet being blocked during operation, etc. 

h) Malfunctions that occur, when the pump is damaged as a result of being dropped or falling, etc. 

i)  Malfunctions  which  are  determined  by  the  manufacturer

s  technical  personnel  to  be  caused  by 

conditions that do not comply with the usage conditions for this vacuum pump. 

j) Malfunctions due to the replacement of consumables.         

(4) Disclaimer 

a) We shall not be liable for any malfunctions of our products caused by the customer, regardless if 

the  malfunction  does  not  fall  within  the  warranty  period,  nor  shall  we  be  liable  for  any  loss  of 

opportunity  for  the  customer

s  clients  or  for  compensation  for  any  damages  to  other  products, 

labor costs, production loss, transportation expenses and other related work.   

b)  We  shall  not  be  liable  for  any  claims  and  patent  infringements,  including  secondary  damages, 

filed a claim by a third party against the customer.

 

Содержание DAL-181D




































Отзывы: