3
Programming Process
I. Key Information – provided as a example only – you need to determine values for each for your lift:
Motor tube diameter
:
51.1
mm
Motor rpm
:
12
turns/minute
Show position
:
1500
mm from home/closed position (measured from bottom of the projector lift frame)
Service position
:
3000
mm from home/closed position (measured from bottom of the projector lift frame)
The
Service position (
fully lowered
) is not programmed here. It is adjusted using the limit
switch on the tubular motor. Please refer to the “Wiring-Adjusting Motor Limits” section of
the Prolift Product Manual.
II. Calculations:
1.
Motor tube circumference =
π
x D =
3.14159
x
51.1
=
160.535
mm
2.
Rate of turn(sec) = rpm x result(1)/60 =
12
turns/min x
160.535
mm/turn divided by 60 sec =
32.107
mm/sec
3.
Show position travel time (sec) = Show position/rate of turn =
1500
mm/
32.107
=
46.71
seconds
4.
Maximum travel time (sec) = Service position/rate of turn =
3000
/
32.107
=
93.43
or
93
seconds
5.
Show position travel time, in %, away from reference = result(3)/result(4) =
46.71
/
93
x 100 = 50.22 or
50
%
III. Programming steps
(see IV. Programming instructions using the 24-channel Programming IR/RF Remote Transmitter.)
:
1.
On the programming line 7 below, enter the calculation result of number 4 above, i.e.
093
.
2.
On the programming line 8 below, enter the calculation result of number 5 above, i.e.
50
.
3.
To fine tune viewing height, do steps 14 & 15 below.
Command
Description
1
Stop+O7+C7>Open ALL
(press & hold for >5 sec.)
>
Stop
Clears and restores all memory to factory default
2
Stop+O7+C7>O1>C1>O
2
>Stop
Assign the main channel to Channel 2 of remote transmitter
(see Figure 2)
3
Stop +O7+C7>O2>C2>O
1
>Stop
Assign Show Position to Channel 1 of remote transmitter
(see figure 2)
5
Stop +O7+C7>O2>C10>O2>Stop
Enable memory A & B to Channel 1 of remote transmitter
(see figure 2)
6
Stop +O7+C7>O2>C10>O11>Stop
Change reference for travel time to bottom (or close position) limit
7
Stop +O7+C7>O2>C10>O13>O
10
>O
9
>O
3
>Stop
Set maximum travel time (001 to 299 sec). press Open
10
for zero
8
Stop +O7+C7>O2>C11>O
5
>O
10
>Stop
Set travel time of memory A (open button) to
xy
% away from reference
9
Stop +O7+C7>O2>C12>O
10
>O
10
>Stop
Set travel time of memory B (close button) to
0
% away from reference
10 Stop +O7+C7>O2>C10>O8>Stop
Enable memory positions A & B on manual/dry contact input
(see figure 1)
14 Stop +O7+C7>O2>C11>
O11*
>Stop
Nudge position** of memory A 1/40
th
second away from the reference
15 Stop +O7+C7>O2>C11>
O12*
>Stop
Nudge position** of memory A 1/40
th
second towards the reference
Note: * Press Open 11 (
O11)
or Open 12 (
O12)
as many times as desired before pressing STOP
** 1 Nudge Position (1 Green color flashing on the RP60ABMH controller LED) is approximately 1 mm drop/movement
Содержание Prolift Advanced
Страница 5: ...5 Reference figures...
Страница 6: ...6...
