background image

1

USER INSTRUCTION MANUAL

MODEL:  

96602NS, 96602,  96602N,  96701S,  96701,  96702,

96701SAAA,  96702ACA,  96602ACA

DESCRIPTION:  

REBAR ASSEMBLIES

MEETS OSHA & ANSI Z359.1

1-800-850-5914

PHOENIX, AZ USA

WWW.ULTRASAFEUSA.COM

MODEL: 

__________________________

SIZE: ____________________

DATE: ___________________

Anchorage:

The anchorage to which this product

is attached must be capable of sustaining a static
load in the direction applied by the personal fall
arrest system of at least 3600 lbs. with
certification of a qualified person or 5000 lbs.
without certification. When more than one
personal fall arrest system is attached to the
same structure, the strength requirements stated
above must be multiplied by the number of
personal arrest systems attached to the
structure. 

Plan your personal fall protection system. 

Before installing and using this equipment,
consider all factors affecting your safety 
during use of this equipment. 

Warning:

Manufacturer's instructions supplied

with this product at time of shipment must be
followed. Failure to do so could result in serious
injury or death. Contact manufacturer if
instructions are needed. 

• Warnings and instructions must be read and

understood before using equipment. 

• Equipment must be used by trained 

personnel only. 

• Users must understand all OSHA regulations,

ANSI standards, and other relevant
regulations and standards pertaining to fall
protection equipment. 

This product is part of a
personal fall arrest
system; a fall arrest
system is required if
there is any risk that a
worker may fall from an
elevated position. It is a
requirement that the fall
arrest system be used
any time a working
height of six feet or more
is reached. Working
height is defined as the

distance from the walking/working surface to a
grade or lower level.

The following is recommended as part of fall 
arrest system. 

A. Full Body Harness Material: Nylon

1.  Back D-ring is for fall arrest 
2.  Shoulder D-rings (if present) are

for retrieval use only. 

3.  Side D-rings (if present) are

for positioning only. 

4.  Warning tags.

Note:

Maximum free-fall distance six feet or maximum

fall arrest force of 1800 lbs. Avoid lower level contact.

B. Shock Absorbing Lanyard Material: Nylon

Warning tags located 
in front and back of
shock absorber or
located towards hook,
D-ring or eye end.

• Energy absorber resting force 900 lbs. 

Plus 42 inch maximum extension. 

• Rig lanyard to allow a maximum free fall distance

of not more than six feet. 

• Connectors and anchorage points must be 

compatible and able to support 5,000 lbs. 

•  Do not allow lanyard to contact sharp or abrasive

surfaces, sparks or temperature above 180 degrees. 

• Snap hooks with gate openings larger than 

one inch (1") must not be connected to D-rings 
on harnesses and belts. 

• Remove from service if any damage is detected.

C. Anchorage connector material: Nylon

Warning tags are 
located towards hook, 
D-ring or eye end. 

•  Use energy absorbers or retractable lanyards 

when hazard of free fall can occur. 

• Connectors and anchorage points must be compatible

and able to support 5,000 lbs. Always work directly
under anchorage to avoid a swing fall injury. 

• Anchorage and tie off points must be at a height 

that will not allow a lower level to be struck should 
a fall occur. Do not allow product to contact sharp 
or abrasive surfaces, sparks or temperatures 
above 180 degrees. 

• Snap hooks with gate openings larger than 

one inch (1”) must not be connected. 

• Remove from service if any damage is detected.

313RA1

96602NS

96602

96602N

96701S

96602N

96701S

96702ACA

96602ACA

Содержание 96602NS

Страница 1: ...x feet or more is reached Working height is defined as the distance from the walking working surface to a grade or lower level The following is recommended as part of fall arrest system A Full Body Harness Material Nylon 1 Back D ring is for fall arrest 2 Shoulder D rings if present are for retrieval use only 3 Side D rings if present are for positioning only 4 Warning tags Note Maximum free fall ...

Страница 2: ...ersons trained in its correct application and use APPLICABLE STANDARDS Refer to national standards including the ANSI Z359 family of standards on fall protection ANSI A10 32 and applicable local state and federal OSHA requirements governing occupational safety for more information on work positioning systems ANCHORAGE STRENGTH Anchorages selected for work positioning systems shall have a strength ...

Страница 3: ...ld not be distorted and should roll freely 6 Friction slide adjusters Friction slide adjusters should be checked for sharp edges distortion Make sure that the outer bars and center bars are straight Also check corners and attachment points for wear and cracks 7 Easy connect buckle Easy connect buckle square rings should be checked for distortion sharp edges and cracks For stitched attachment point...

Страница 4: ...oved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By Approved By WARNING The user must read and understand these instructions or have them explained to them before using this equipment Failure to follow instructions may result in serious injury or death INSPECTION AND MAINTENANCE LOG ...

Отзывы: