WARNING!
This product is part of a personal fall
arrest system. The user must read and
follow the manufacturer’s instructions for
each component of the system. These
instructions must be provided to the user
of this product. The user must read and
understand these instructions before
using this product. Manufacturer’s
instructions must be followed for proper
use and maintenance of this product.
Alteration or misuse of this product, or
failure to follow instructions may result in
serious injury or death.
1
MODEL:
__________________________
SIZE: ____________________
DATE: ___________________
Same, but 100% Tie-Off.
313L6
USER INSTRUCTION MANUAL
DESCRIPTION:
LANYARD WITH SHOCK PACKS
3600 LB GATE HOOKS
MODEL:
96516HD, 96516YHD, 96516YCTHD, 96516YCTHDD,
96516YCTHDDE
MEETS OSHA & ANSI Z359.1
APPROVED FOR SHARP LEADING EDGE
1-800-850-5914
PHOENIX, AZ USA
WATCH VIDEO 6 ON ULTRASAFEUSA.COM
Anchorage:
The anchorage to which this product is
attached must be capable of sustaining a static load in
the direction applied by the personal fall arrest system
of at least 3600 lbs. with certification of a qualified
person or 5000 lbs. without certification. When more
than one personal fall arrest system is attached to the
same structure, the strength requirements stated
above must be multiplied by the number of personal
arrest systems attached to the structure.
Plan your personal fall protection system.
Before installing and using this equipment, consider
all factors affecting your safety during use of this
equipment.
Warning:
Manufacturer's instructions supplied with
this product at time of shipment must be followed.
Failure to do so could result in serious injury or death.
Contact manufacturer if instructions are needed.
• Warnings and instructions must be read and
understood before using equipment.
• Equipment must be used by trained personnel only.
• Users must understand all OSHA regulations, ANSI
standards, and other relevant regulations and
standards pertaining to fall protection equipment.
This product is part of a personal fall
arrest system; a fall arrest system is
required if there is any risk that a worker
may fall from an elevated position. It is a
requirement that the fall arrest system be
used any time a working height of six feet
or more is reached. Working height is
defined as the distance from the walking /
working surface to a grade or lower level.
THE FOLLOWING IS RECOMMENDED
AS PART OF FALL ARREST SYSTEM.
Note:
See additional instructions on buckle
adjustment for proper fit. Maximum free-fall distance
six feet or maximum fall arrest force of 1800 lbs.
Avoid lower level contact.
Shock Absorbing
Lanyard Material: Nylon
Warning tags located
in front and back of
shock absorber or
located towards hook,
D-ring or eye end.
• Energy absorber resting force 900 lbs.
Plus 42 inch maximum extension.
• Rig lanyard to allow a maximum free fall distance
of not more than six feet.
• Connectors and anchorage points must be
compatible and able to support 5,000 lbs.
• Do not allow lanyard to contact sharp or abrasive
surfaces, sparks or temperature above 180 degrees.
• Snap hooks with gate openings larger than
one inch (1") must not be connected to D-rings
on harnesses and belts.
• Remove from service if any damage is detected.
Anchorage connector
material: Nylon
Warning tags are
located towards hook,
D-ring or eye end.
• Use energy absorbers or retractable lanyards
when hazard of free fall can occur.
• Connectors and anchorage points must be compatible
and able to support 5,000 lbs. Always work directly
under anchorage to avoid a swing fall injury.
• Anchorage and tie off points must be at a height
that will not allow a lower level to be struck should
a fall occur. Do not allow product to contact sharp
or abrasive surfaces, sparks or temperatures
above 180 degrees.
• Snap hooks with gate openings larger than
one inch (1”) must not be connected.
• Remove from service if any damage is detected.
1.
2.
3.
4.
5.
6.
7.
1. Back 'D' ring is for fall arrest
2. Shoulder 'D' rings. (if present) are for retrieval use
only use locking snaps.
3. Side 'D' rings (if present) are for positioning only.
4. Front 'D' ring (if present) is for fall arrest
(foot first falls only, 2 foot max free fall), work
positioning, travel restraint or rescue
5. Hip attachment elements are for work positioning
or travel restraint
6. Visual load indicator
7. Park lanyard here
NOTE:
See additional instructions on buckle adjustment for proper fit. Maximum free-fall
distance six feet or energy absorber arresting force of 900 lbs per ANSI or maximum fall arrest
force of 1800 lbs per OSHA.Avoid lower level contact.
