manualshive.com logo in svg

UHVD MD40, Инструкция по эксплуатации товара, Страница: 11 / 55

Поделиться
Скачать
UHVD MD40 Скачать руководство пользователя страница 11

MD40 

PRODUCT INSTRUCTION MANUAL                              

 

 

 

MD40 

Page 11 of 55 

Author: N.Carapiet | Revision: 1.1 

1.

 

Insert MD40 flange assembly

 

2.

 

Insert bolts and tighten.

 

Note: when tightening bolts, care must be taken not to tighten 
them unevenly as this may cause the gasket not to seal properly.

 

 

STAGE 3

 

| Replace thimble and associated parts.

 

 

 

How to re-install the Drive Thimble: 

1.

 

Push Drive Thimble over the Flange Assembly (take care when re-coupling the magnets 

–

 

the magnetic coupling may cause a sudden movement)

 

2.

 

Replace Bearing Cap

 

3.

 

Insert and tighten 3 x M3 Grub Screws

 

4.

 

Replace Dual Shaft End Cap (ensure that the drive pin locates in the drive slot)

 

5.

 

Insert and tighten 3 x M3 Grub Screws

 

 

2.1.5  Bakeout procedure 

The manual drives can be baked to 250

o

C without the need to remove any components.  

In the case of the dual shaft version

, please refer to the manufacturer’s instructions relating to any 

motors/pulleys you may have installed onto the MagiDrive. 

 

 

 

 

End Cap 

3 x M2.5 Grub Screws 

Bearing Cap 

Drive Thimble 

3 x M2.5 Grub Screws 

Содержание MD40
























































Отзывы:

Нет отзывов