background image

7

PRE TEST CHECKLIST

SETTING INLET TEMPERATURE

ANALYZER CONNECTIONS

•   Turn on and zero the analyzer, without the flue probe connected, to use ambient temperature

•   Connect the flue probe thermocouple to T1 during zero countdown use for inlet ducted system

•   Connect a thermocouple to T2 to measure second temp source

•  Clean particle filter 
•  Water trap and probe line are empty of water
•  Power on and zero
•  All hose and thermocouple connections are properly secured

•  Flue gas probe is sampling ambient FRESH air
•  Water trap is fitted correctly to the instrument
•  Flue temperature plug is connected
•  Ensure water trap plug is inserted correctly

 

WARNING

Turning the pump off while the probe is in the flue will leave toxic gases inside the analyzer. Once 

data has been printed or copied, it is advisable to purge the unit with fresh air as soon as possible. 

To do this remove the probe from the flue and turn ON pump. Always allow the readings to return to 

zero (20.9% for O

2

) prior to shutting the unit off. The meter will not switch off until the CO reading is 

below 20 ppm.

 

CAUTION

The probe will be hot from flue gases. Remove the probe from the flue and allow it to cool naturally. 

Do not immerse the probe in water, as this will be drawn into the analyzer and damage the flue 

probe and the pump and sensors. 

NOTE: 

Take care when 

inserting the temperature 

probes as the pins are 

polarized. Insert with the 

smaller pin (+) to the right. 

T2

T1

P2

P1

•   Remove the protective rubber boot

•   Slide the water trap unit from the analyzer

•   Remove the particle filter from its’ spigot and replace

•   Slide the water trap back into position and replace the protective rubber boot

EMPTYING & CLEANING THE IN-LINE WATER TRAP

CHANGING THE PARTICLE FILTER

QUICK START

Turn on the analyzer by pressing the On/Off Button for 2 seconds until the unit activates. As described the analyzer will perform a 60 

second turn on purge. Once completed simply select the reading desired by the position of the rotary dial.

•   Remove the rubber plug

•   Allow the water to drain out

•   Re-insert the rubber plug

www.calcert.com

[email protected]

1.800.544.2843

0

5

10

15

20

25

30

Содержание 053533509175



























Отзывы: