Udoo VISION Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 67

Udoo VISION Скачать руководство пользователя страница 30

VISION

UDOO VISION User Manual - Rev. First Edition: 1.0 - Last Edition: 1.0 - Author: A.R. - Reviewed by M.B. Copyright © 2021 SECO S.p.A

30

3.3.5

+ Connector

On the UDOO VISION board, the Digital Display Interfaces #0 is
used to implement a multimode Display Port (DP++) interface, i.e. it
can be used to support DP displays directly and, through an external
adapter, also HDMI or DVI displays.

Such an interface is available on miniDP connector, type ADAM-TECH p/n MDPC-S-
RA-KT-TR or equivalent, with the pinout shown in the table on the left.

The configuration of this interface in DP or HDMI/DVI mode is automatic, and it is
driven by the DP0_CAD signal available on pin 4.

When  a  DP  cable  is  connected,  then  the  DP0_CAD  signal  is  not  connected;  this
interface will recognize it, and on pins 16/18 there will be the Display Port Auxiliary
channel  signals.  Instead,  when  a  DP-to-HDMI  adapter  is  mounted,  it  will  drive
opportunely  the  DP0_CAD  signal,  which  will make  available  HDMI_CTRL_CLK  and
HDMI_CTRL_DAT signals on the same pins.

Further signals involved in DP management are the following:

DP/DP0_LANE0-: Display Port differential pair #0.

DP/DP0_LANE1-: Display Port differential pair #1.

DP/DP0_LANE2-: Display Port differential pair #2.

DP/DP0_LANE3-: Display Port differential pair #3.

DP0_HPD: Hot Plug Detect Input signal.

HDMI0_CEC: HDMI Consumer Electronics Control (CEC) Line. This signal is used only for HDMI compatibility when a HDMI adapter is connected to the DP connector.

+ Connector- CN21

Pin Signal

Pin Signal

1

GND

2

DP0_HPD

3

DP

4

DP0_CAD

5

DP0_LANE0-

6

DP0_CEC

7

GND

8

GND

9

DP

10

DP

11

DP0_LANE1-

12

DP0_LANE3-

13

GND

14

GND

15

DP

16

HDMI0_CTRL_CLK /

17

DP0_LANE2-

18

HDMI0_CTRL_DAT / DP0_AUX-

19

GND

20

+3.3V_RUN

«
...
28
29
30
31
32
...
»

Содержание VISION




































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды