UCL SWIFT SWIFT KR12 страница 65 Скачать руководство пользователя

Страница: 65 / 75

��

ERROR MESSAGE

Too Dirty Fiber

It is displayed when the ﬁber prepared
for splice is contaminated more than
normal status.

HOW TO

· Reset the ﬁber after cleaning.

Replace The Fiber In The

Correct Position

It is displayed when the ﬁber is not
placed in the middle of the electrodes
and V�groove or the objective lenses
or reﬂection mirror is contaminated.

HOW TO

· Press and place the ﬁber
in the middle of the electrodes
and V�groove.
· Check the condition of the lenses
and reﬂectionmirror and remove
any dirt.

Too Long Fiber

It is displayed when the ﬁber is
placed too close to the electrode, the
lenses or reﬂection mirror is dirty or
LED light is not bright enough.

HOW TO

· Press and place the ﬁber
again.
· Remove dust and dirt from the
lenses and reﬂection mirror.
· Conduct an LED test. If an error
occurs, contact UCLSWIFT Co., Ltd

RESET

ERROR MESSAGE

Содержание SWIFT KR12












































































Результаты поиска

Содержание SWIFT KR12

Отзывы:

Похожие инструкции для SWIFT KR12

Бренды по названию

Популярные бренды

UCL SWIFT SWIFT KR12, Руководство пользователя

Результаты поиска

Содержание SWIFT KR12

Отзывы:

Похожие инструкции для SWIFT KR12

Бренды по названию

Популярные бренды