manualshive.com logo in svg

Ublox SARA-R4 Series, Руководство по управлению

Поделиться
Скачать
Ublox SARA-R4 Series Скачать руководство пользователя страница 217

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

 

21    HTTP

Page 217 of 307

21    HTTP

The section describes the u-blox proprietary AT commands that can be used for sending requests to a remote
HTTP  server,  receiving  the  server  response  and  transparently  storing  it  in  the  file  system.  The  supported
methods are: HEAD, GET, DELETE, PUT, POST file and POST data. A PSD or CSD connection must be activated
before using HTTP AT commands.

When these commands report an HTTP error, the error code can be queried using the 

+UHTTPER

 AT command.

SARA-R4
No need to establish a PSD connection explicitly. This device automatically establishes a PSD connection
as part of the network registration and attach procedure.

21.1    HTTP cUHTTP

+UHTTP

SARA-R404M SARA-R410M-01B SARA-R410M-02B SARA-R410M-52B SARA-R412M

Modules

SARA-N4

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

partial

No

No

No

-

Appendix A.6

21.1.1    Description

Configures, reads or resets (to the factory-programmed values) the HTTP application profile parameters. Up
to 4 different HTTP profiles can be defined. To set all the parameters in an HTTP profile a set command for
each <op_code> needs to be issued.

The configured HTTP profile parameters are not saved in the non volatile memory.

The read command has two possible usages. The functionality of the command differs with the number
of command parameters issued:
• Only the first command parameter (<profile_id>) issued: the module resets all the profile parameters

(to the factory-programmed values) for the profile specified with <profile_id>

• Only the first and second command parameters used (<profile_id>, <op_code>): the module returns

the current value of the profile parameter specified with <op_code> and related to the profile specified
with <profile_id>

21.1.2    Syntax

Type

Syntax

Response

Example

Generic syntax

Set

AT+UHTTP=<profile_id>,<op_
code>,<param_val>[,<param_val1>]

OK

AT+UHTTP=2,0,"125.24.51.133"

OK

Read

AT+UHTTP=<profile_id>,<op_code> +UHTTP: <profile_id>,<op_code>,

<param_val>[,<param_val1>]

OK

AT+UHTTP=2,0

+UHTTP: 2,0,"125.24.51.133"

OK

HTTP server IP address

Set

AT+UHTTP=<profile_id>,0,<HTTP_
server_IP_address>

OK

AT+UHTTP=2,0,"125.24.51.133"

OK

Read

AT+UHTTP=<profile_id>,0

+UHTTP: <profile_id>,0,<HTTP_
server_IP_address>

OK

AT+UHTTP=2,0

+UHTTP: 2,0,"125.24.51.133"

OK

HTTP server name

Set

AT+UHTTP=<profile_id>,1,<HTTP_
server_name>

OK

AT+UHTTP=2,1,"www.u-blox.com"

OK

Read

AT+UHTTP=<profile_id>,1

+UHTTP: <profile_id>,1,<HTTP_
server_name>

OK

AT+UHTTP=2,1

+UHTTP: 2,1,"www.u-blox.com"

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды